These axle shafts are just what you need to get your vehicle in good working order!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • CV style axle shafts
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge
  • Correct for models with or without ABS (Anti-Lock Brakes)

These cv axle shafts make great replacements and have good cost savings over the dealer units!

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:45)
    • Pry off the hub cap with a flat blade screwdriver
    • Loosen the 35mm hub nut with the vehicle on the ground
    • Loosen the lug nuts
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Rotor (1:28)
    • Remove the 17mm bolts from the brake caliper while using an 18mm wrench to hold the inside nut
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
    • If the rotor will not come off hit the rotor with a ball peen hammer
    • If the rotor still won't come off, thread the bolts into the press holes and slide the rotor off
    • Remove the center hub nut
  3. step : Removing the Axle (2:57)
    • Remove the 15mm bolts from the panel to access the driver side
    • Remove the 15mm bolts from the control arm with a socket, ratchet, and wrench
    • Hammer the upper control arm off the ball joint
    • Pry open the clip and remove the brake line wiring harness
    • Wire-tire the caliper onto the backing plate
    • Remove the two 10mm bolts from the brake line bracket
    • Pull the control arm back from the steering knuckle
    • Place a pry bar onto the back of the axle where it connects to the transmission
    • Hammer the pry bar to push the axle out
    • Place a drip pan underneath the differential
    • Maneuver the axle out of the differential
  4. step : Installing the Axle (6:03)
    • Fit the axle into the hub and then push it into place
    • As you go, place the steering knuckle into the ball joint on the control arm
    • Make sure the axle is locked
    • Replace the brake line bracket
    • Insert and tighten the 10mm bolts to the brake line bracket
    • Re-clip the harness to the brake line
    • Hammer the upper control arm onto the ball joint
    • Replace and tighten the 15mm bolts to the control arm
    • Torque the 15mm bolt to 55 to 60 ft/lbs
  5. step : Installing the Rotor (8:29)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Apply brake grease to the caliper bracket bolts
    • Put the bracket back into place
    • Start the 18mm bolts by hand and tighten them
    • Torque the bolts to 110 ft/lbs of torque
    • Install the new brake pads into the bracket
    • Apply brake grease to the brake pads
    • Put the caliper on
    • Thread the 17mm bolts by hand
    • Torque bolts to 40 ft/lbs
    • Replace the hub nut and remove the lug nut
  6. step : Reattaching the Wheel (10:21)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut
    • Torque the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Torque the hub nut to 103 ft/lbs
    • Reattach the center cap
  7. step : Testing the Brakes (11:19)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Floor Jack
  • Jack Stands
  • Drain Pan

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 35mm Socket
  • 19mm Socket
  • 17mm Socket
  • 10mm Socket
  • 15mm Socket

  • Wrenches - Metric

  • 15mm Wrench
  • 18mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Fit perfect and great price.
Everything for as it should. Fast shipping, great price. Can't get any better.
June 30, 2017
Purchased
9 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 3 answers
Do these come with the nuts?
Colter L on Feb 19, 2017
BEST ANSWER: Yes, both shafts come with a new locking nut. Just be aware that the new nut is a 36mm vice the stock 35mm so be sure you have the appropriate deep socket impact size ready when reinstalling.

How-to Video:

(11:48 min)

Tools List:

    General Tools

  • Hammer
  • Floor Jack
  • Jack Stands
  • Drain Pan

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner

  • Ratchets & Related

  • Torque Wrench
  • Ratchet
  • A Piece of Pipe (for leverage)

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 35mm Socket
  • 19mm Socket
  • 17mm Socket
  • 10mm Socket
  • 15mm Socket

  • Wrenches - Metric

  • 15mm Wrench
  • 18mm Wrench




Vehicle Fit

  • 2004-2007 Buick Rainier Pair CV Axle Shaft Front
  • 2002-2009 Chevy Trailblazer Pair CV Axle Shaft Front
  • 2002-2006 Chevy Trailblazer EXT Pair CV Axle Shaft Front
  • 2002-2009 GMC Envoy Pair CV Axle Shaft Front
  • 2002-2006 GMC Envoy XL Pair CV Axle Shaft Front
  • 2004-2005 GMC Envoy XUV Pair CV Axle Shaft Front
  • 2003-2008 Isuzu Ascender Pair CV Axle Shaft Front
  • 2002-2004 Olds Bravada Pair CV Axle Shaft Front
  • 2005-2009 Saab 9-7X Pair CV Axle Shaft Front
Part #: 1AACS00087

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More