CV Axle Shaft Front Pair A1 Cardone 66-1345 - CAACS00011

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   Pair
  • Front or Rear Location:   Front

These axle shafts are new, aftermarket parts. They are just what you need to get your vehicle in good working order!


  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • CV Style Axle Shafts
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charges
  • Correct for models with or without ABS (Anti-Lock Brakes)

Features & Benefits of each NEW CV (Constant Velocity) axle shaft:

  • 100% Neoprene Boots for excellent Ozone resistance. - Eliminates cracking; a leading cause for failure of CV boots
  • 3% moly grease. - Provides excellent high temperature and extreme pressure characteristics which extends the life of the joint
  • Axle nut supplied 100%. - If axle nut from the vehicle is worn or stripped there is no need to buy a separate axle nut because it is provided
  • Splines rolled 100%. - Guarantees proper installation of axle into mating hub and transmission eliminating installation hassle
  • Threads rolled 100%. - Guarantees proper installation of axle nut eliminating installation hassle

Note: This is for a pair of axle shaft assemblies.

Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:22)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:49)
    • Pry the brake pads in with a flat blade screwdriver to push in the pistons
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry out the brake pads with a flat blade screwdriver
  3. step : Removing the Brake Rotor (2:20)
    • Remove two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
    • If the rotor will not pull off thread two M10 by 7cm bolts into the threaded holes
    • For more detailed instructions, please see the 2004 Trailblazer rear brake replacement video
  4. step : Accessing the Differential (3:31)
    • Have a drain pan ready
    • Remove all but two bolts from the differential cover
    • Drain the differential fluid
  5. step : Removing the Axle (4:20)
    • Put the vehicle into neutral
    • Turn the driveshaft by hand until you can access the differential bolt
    • Remove the 5/16 inch bolt from the differential
    • Pull the clip from the differential
    • Slide out the differential pin
    • Push the axle inward by hand
    • Pull out the small C-clamp from the differential
    • Pull the axle out by hand
  6. step : Installing the New Axle (5:58)
    • Slide the axle in being sure not to drag against the seal
    • Install the C-clamp onto the axle with the grooved side toward the center
    • Push the axle out by hand
    • Line the gears up by hand
    • Insert the differential pin
    • Start the 5/16 inch bolt into the differential
    • Apply thread locking fluid to the 5/16 inch bolt
    • Tighten the 5/16 inch bolt to between 8 -10 foot-pounds of torque
  7. step : Reinstalling the Differential Cover (8:28)
    • Clean the mounting area with a cloth rag
    • Clean the differential cover with a cloth rag
    • Apply sealant to the gasket cover
    • Put the gasket and differential cover into place
    • Start two bolts into the differential cover by hand
    • Start the remaining bolts
    • Tighten the bolts to about 12 foot-pounds
  8. step : Refilling the Rear End (9:50)
    • Remove the differential plug with a 3/8 inch drive ratchet
    • Fill the differential with 80w-90 gear oil, until fluid begins to leak out
    • Put the plug back in and tighten it
    • Clean grease off the rear end
  9. step : Reinstalling the Brake Rotor (10:35)
    • Slide the rotor on
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts
  10. step : Reinstalling the Brake Pads (11:02)
    • Install the new brake pads into the bracket with the wear indicator on the lower side
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten the 14mm bolts
  11. step : Reattaching the Wheel (11:30)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 - 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  12. step : Testing the Brakes (12:05)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Drain Pan
  • Floor Jack
  • Funnel
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Cloth Rags
  • Gasket Adhesive
  • Gear Oil
  • Liquid Thread Locker
  • M10 x 7cm bolts

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • 3/8 Inch Drive Ratchet
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Sockets - SAE

  • Complete SAE Socket Set

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2007Buick Rainier Buick Rainier Front CV Axle Shaft Pair A1 Cardone 66-1345
2002-2009Chevy Trailblazer Chevy Trailblazer Front CV Axle Shaft Pair A1 Cardone 66-1345
2002-2006Chevy Trailblazer EXT Chevy Trailblazer EXT Front CV Axle Shaft Pair A1 Cardone 66-1345
2002-2009GMC Envoy GMC Envoy Front CV Axle Shaft Pair A1 Cardone 66-1345
2002-2006GMC Envoy XL GMC Envoy XL Front CV Axle Shaft Pair A1 Cardone 66-1345
2004-2005GMC Envoy XUV GMC Envoy XUV Front CV Axle Shaft Pair A1 Cardone 66-1345
2003-2008Isuzu Ascender Isuzu Ascender Front CV Axle Shaft Pair A1 Cardone 66-1345
2002-2004Oldsmobile Bravada Olds Bravada Front CV Axle Shaft Pair A1 Cardone 66-1345
2005-2009Saab 9-7X Saab 9-7X Front CV Axle Shaft Pair A1 Cardone 66-1345
Part #: CAACS00011

Out of Stock

Brand #: 66-1345

How-to Video:

(12:35 min)