This replacement Crankshaft Position Sensor is just what you need to get your vehicle in good running condition again!

A bad or malfunctioning crank sensor will often cause a service engine light error code, and or cause a no start condition, or rough running due to inaccurate ignition and fuel timing.

This Crank Sensor features:

  • Built to strict quality control standards
  • Direct replacement
  • 100% factory tested

Your Engine size can usually be found on a white sticker in the engine compartment near the radiator. If needed, your VIN code is the 8th digit of your vehicles Vehicle Identification number. The VIN can be found on the bottom drivers side corner of the windshield and on your registration. Some refer to the VIN code as the Serial Number.

 

 

Our electrical and electronic parts are subject to strict quality control testing .  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Loosening the A/C Compressor (0:25)
    • Locate the sensor between the A/C compressor and harmonic balancer pulley
    • Insert a 1/4" ratchet into the tensioner
    • Turn the tensioner clockwise
    • Slide the belt off of the A/C compressor pulley
    • Tuck the belt up above the compressor pulley
    • Remove the three 10mm bolts beneath the compressor
    • Slide the compressor over
  2. step : Removing the Crankshaft Position Sensor (3:09)
    • Remove the 8mm bolt from the compressor
    • Disconnect the wiring harness
    • Turn the sensor
    • Remove the sensor
  3. step : Installing the Crankshaft Position Sensor (4:12)
    • Apply motor oil to the seal
    • Click the crankshaft position sensor into place
    • Tighten the 8mm bolt to the sensor
  4. step : Tightening the A/C Compressor (5:22)
    • Lift the A/C compressor and line up the bolt holes
    • Hand-tighten the 10mm bolts to the compressor
    • Tighten the bolts with a ratchet and socket
    • Connect the crankshaft position sensor wiring harness
    • Insert the 1/4" ratchet into the tensioner
    • Pull the ratchet clockwise
    • Loop the bolt onto the A/C compressor pulley

Tools needed for replacement:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • Swivel

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 8mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(07:20 min)

Tools List:

    Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Socket Extensions
  • Ratchet
  • Swivel

  • Sockets - Metric

  • 8mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 8mm Wrench



This part replaces:

  • OE # F1AZ6C315A
  • Standard Motor Products PC18T

Vehicle Fit

  • 1992-1998 Ford Crown Victoria Crankshaft Position Sensor
  • 1997-2008 Ford E150 Van Crankshaft Position Sensor V8 5.4L
  • 1997-1999 Ford E150 Van Crankshaft Position Sensor V8 4.6L
  • 1997-1999 Ford E250 Van Crankshaft Position Sensor V8 5.4L
  • 1997-1999 Ford E250 Van Crankshaft Position Sensor V8 4.6L
  • 1997-1999 Ford E350 Van Crankshaft Position Sensor V8 5.4L
  • 1997-1999 Ford E350 Van Crankshaft Position Sensor V10 6.8L
  • 1997-1999 Ford Expedition Crankshaft Position Sensor
  • 1997-1999 Ford F150 Truck Crankshaft Position Sensor V8 5.4L
  • 1997-1999 Ford F150 Truck Crankshaft Position Sensor V8 4.6L
  • 1997-1999 Ford F250 Light Duty Truck Crankshaft Position Sensor V8 4.6L
  • 1997-1999 Ford F250 Light Duty Truck Crankshaft Position Sensor V8 5.4L
  • 1996-1998 Ford Mustang Crankshaft Position Sensor V8 4.6L
  • 1994-1997 Ford Thunderbird Crankshaft Position Sensor V8 4.6L
  • 1993-1998 Lincoln Mark VIII Crankshaft Position Sensor
  • 1991-1998 Lincoln Town Car Crankshaft Position Sensor
  • 1994-1997 Mercury Cougar Crankshaft Position Sensor V8 4.6L
  • 1992-1998 Mercury Grand Marquis Crankshaft Position Sensor
Part #: 1AECS00006

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More