Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This replacement front upper control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits RH (Passenger Side) FRONT UPPER
  • Replaces dealer part numbers: 4616922, 4764408, 4782974, 4764408AC, 4782974AB, 4782974AE
  • Includes new ball joint
  • Bushings not included
  • Control arm is new, not remanufactured or refurbished

Worn ball joints or loose rear bushings can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace that heavily rusted, rotted, or damaged front upper control arm with the loose bushings or worn ball joints with our high quality all in one replacement.

One way to diagnose a loose, or warn ball joint on a control arm, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint and bushings for play, if it is moving you probably need to replace it.

Our control arms are designed to be direct replacements for the original factory parts.  They are 100% brand new and require no modifications for installation.  No special tools are required because all of the bushings come pre-installed.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

    It is recommended to receive a professional alignment after completing this repair

  1. step : Removing the Wheel (0:43)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Outer Tie Rod (1:05)
    • Use a pair of pliers to straighten the cotter pin and remove it
    • Remove the castle nut with an adjustable wrench
    • Measure the distance from the inner tie rod to the outer tie rod
    • Loosen the nut between the inner and outer tie rod
    • Hammer the knuckle to loosen the outer tie rod
    • Remove the outer tie rod and twist it off the inner tie rod
  3. step : Installing the Outer Tie Rod (2:05)
    • Twist the grease filler into the new outer tie rod
    • Twist the outer tie rod to the inner tie rod
    • Measure the distance and make sure it matches the recorded distance
    • Tighten the nut between the inner and outer tie rod
    • Insert the outer tie rod to the knuckle
    • Replace and tighten the castle nut while lining up the cotter pin hole
    • Insert the cotter pin and twist the ends with a pair of pliers
    • Fill up the grease filler with a grease gun
  4. step : Reattaching the Wheel (3:21)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Hammer
  • Measuring Tape
  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Specialty Tools

  • Grease Gun

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Riding smoothly
when I put this on my car it fixed my alignment issue, my car takes bumps and rides like a dream
April 15, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1995-2000Chrysler Cirrus Chrysler Cirrus Front Upper Control Arm with Ball Joint Passenger Side
1997-2000Chrysler Sebring Chrysler Sebring Front Upper Control Arm with Ball Joint Passenger Side
2001-2006Chrysler Sebring Chrysler Sebring Convertible Front Upper Control Arm with Ball Joint Passenger Side
2001-2006Chrysler Sebring Chrysler Sebring Sedan Front Upper Control Arm with Ball Joint Passenger Side
1995-2000Dodge Stratus Dodge Stratus Front Upper Control Arm with Ball Joint Passenger Side
2001-2006Dodge Stratus Dodge Stratus Sedan Front Upper Control Arm with Ball Joint Passenger Side
1996-2000Plymouth Breeze Plymouth Breeze Front Upper Control Arm with Ball Joint Passenger Side
Part #: 1ASFU00032


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(03:52 min)