Replaces

Control Arm with Ball Joint Pair MOOG K8726T, K8728T - MGSFK00054

Specifications:

  • Brand New Control Arms
  • Comes as a Pair
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Step 1: Removing the Wheel (0:55)
    • Remove the center cap.
    • Loosen the lug nuts.
    • Raise the vehicle.
    • Remove the lug nuts.
    • Remove the wheel.
  2. step : Step 2: Removing the Front Upper Control Arm (1:10)
    • Jack up the lower control arm to support the suspension.
    • Mark the upper bolts on the control arm with a marker to remember their alignment. Draw a line on the bolt and on to the bracket.
    • Remove the cotter pin from the balljoint.
    • Spray the ball join and upper bolts with penetrating oil.
    • Us a 21mm socket on the balljoint bolt. Hammer it on.
    • Use a breaker bar and pipe for added leverage to loosen the 21mm bolt. Don’t full remove the bolt.
    • Loosen the other two 21mm bolts using a socket and breaker bar.
    • Remove the nut from the balljoint and use a balljoint puller tool to separate the control arm and steering knuckle.
    • Use a 19mm to tighten the balljoint removal tool until it pops.
    • Remove the upper nuts and bolts.
    • Pull the control arm free.
  3. step : Step 3: Installing the New Control Arm (7:18)
    • Use a wire brush where the control arm goes.
    • Put the new control arm in place.
    • Push it down onto the balljoint and start the bolts.
    • Reinsert the upper bolts. Line the marks up.
    • Torque Ball joint nut to 67ft/lbs.
    • Insert new cotter pin and use pliers to bend the end.
    • Put a grease fitting on and pump grease into the ball joint.
    • Raise the vehicle so all the weight is on the suspension.
    • Torque the upper bolts to 100ft/lbs.
  4. step : Step 4: Reinstalling the Wheel (10:57)
    • Put the wheel in place.
    • Replace the lug nuts.
    • Lower the vehicle.
    • Tighten the lug nuts to 100ft/lbs in a star pattern.
    • Replace the center cap.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Very pleased with the service, the prompt delivery and the quality of the parts. I am also pleased with the improved ride
and handeling of my truck! And I have already told several people about you and how pleased I am.
September 26, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(11:43 min)

Tools List:

    General Tools

  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)

  • Sockets - Metric

  • 19mm Socket
  • 21mm Socket

  • Specialty Tools

  • Ball Joint Press



This part replaces:

  • MOOG K8726T, K8728T
  • Reference Number K8726T
  • Reference Number K8728T

Vehicle Fit

  • 1997-2002 Ford Expedition 2 Wheel Drive Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
  • 2004 Ford F150 Heritage Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
  • 1997-2003 Ford F150 Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
  • 1997-1999 Ford F250 Light Duty Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
  • 1999-2003 Ford F250 Super Duty Truck 2 Wheel Drive Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
  • 2002-2003 Lincoln Blackwood Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
  • 1998-2002 Lincoln Navigator 2 Wheel Drive Front Upper Control Arm with Ball Joint Pair MOOG K8726T, K8728T
Part #: MGSFK00054

Out of Stock

MOOG
Brand #: K8726T, K8728T

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More