Replaces

Control Arm with Ball Joint Front Passenger Side - 1ASLF00082

This replacement front lower control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits RH (Passenger Side) FRONT LOWER
  • Includes new ball joint and bushings
  • Control arm is new, not remanufactured or refurbished

Worn ball joints or loose rear bushings can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace that heavily rusted, rotted, or damaged front lower control arm with the loose bushings or worn ball joints with our high quality all in one replacement.

One way to diagnose a loose, or warn ball joint on a control arm, is to jack the car up, so the wheel is off of the ground, then have someone try to move the wheel in and out. While they are moving the wheel check the ball joint and bushings for play, if it is moving you probably need to replace it.

Part Details

  • Front or Rear Location: Front
  • Location: Lower
  • Side Location: Passenger Side

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:16)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Freeing the Axle from the Hub (1:38)
    • Twist off the hub nut cotter pin with needle nose pliers
    • Remove the hub nut with a 32mm socket and an impact wrench
    • Test that the axle is not seized inside the hub by pushing it in by hand
    • If it is seized, thread on the 32mm bolt by hand and strike the axle with a hammer
  3. step : Moving the Stabilizer Link (2:54)
    • Hold the back of the lower stabilizer link bolt with a 14mm wrench
    • Remove the lower 15mm nut from the stabilizer link
    • Pull the stabilizer link aside
  4. step : Removing the Control Arm (3:42)
    • Apply penetrating oil to the 27mm nut on the control arm
    • Remove the 27mm bolt from the control arm
    • Remove the four 22mm bolts from the control arm alignment bar
    • Remove the two 22mm bolts from the control arm bracket
    • Pull the axle out of the hub
    • Remove the cotter pin from the ball joint with the needle nose pliers
    • Remove the 19mm bolt from the control arm ball joint
    • Strike the steering knuckle with a hammer to loosen the ball joint
    • Pull the ball joint out of the steering knuckle
  5. step : Preparing the New Control Arm (6:58)
    • Transfer the alignment bar from the old to the new control arm
    • Thread the nut onto the alignment bar
  6. step : Installing the New Control Arm (7:14)
    • Push the ball joint into the steering knuckle
    • Fasten the 19mm nut onto the ball joint
    • Tighten the 19mm nut to 45 - 50 foot-pounds of torque
    • Turn the nut further to line up the castle nut with the cotter pin hole
    • Put the cotter pin into the ball joint
    • Bend the cotter pin, making sure it doesn't contact the CV joint
    • Push the axle into the hub
    • Lift the control arm into place
    • Start the 22mm bolts into the alignment bar
    • Start the 22mm bolts into the control arm bracket
    • Tighten the six 22mm bolts to 120 foot-pounds
    • Raise the control arm to its proper ride height with a floor jack
    • Start the 27mm bolt into the control arm
    • Tighten the 27mm bolt to 120 foot-pounds
  7. step : Reinstalling the Stabilizer Link (8:57)
    • Push the stabilizer link back into place
    • Hold the back of the lower stabilizer link bolt with a 14mm wrench
    • Fasten the lower 15mm nut onto the stabilizer link
  8. step : Fastening the Axle to the Hub (9:14)
    • Thread on the center hub nut
    • Have an assistant press the brake pedal
    • Tighten the hub nut to 217 foot-pounds
    • Insert the cotter pin into the hub nut
    • Bend the cotter pin into place with needle nose pliers
    • Push in the transmission fill plug
  9. step : Reattaching the Wheel (9:44)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Have your suspension professionally aligned

Tools needed for replacement:

    Air Powered Tools

  • 1/2 Inch Air Impact Gun

  • General Tools

  • Assistant
  • Floor Jack
  • Jack Stands
  • Hammer
  • Center Punch

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar
  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 32mm Socket
  • 21mm Socket
  • 22mm Socket
  • 15mm Socket
  • 27mm socket

  • Wrenches - Metric

  • 14mm Wrench

4.5 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
Passenger Side Lower Control Arm
I have also looked at there videos online to fix things on my car. And to purchase some parts from them is even better. It got to me on time. And part condition was excellent. Thank you!
June 15, 2018
Purchased
2 months ago
The control arm fit great. I have only driven a few miles since installing the part but so far so good.
July 17, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2000-2001Infiniti I30 Infiniti I30 Front Lower Control Arm with Ball Joint Passenger Side
2002-2004Infiniti I35 Infiniti I35 Front Lower Control Arm with Ball Joint Passenger Side
1999Nissan Maxima Nissan Maxima Front Lower Control Arm with Ball Joint Passenger Side (Built After 4/99 Production Date)
2000-2003Nissan Maxima Nissan Maxima Front Lower Control Arm with Ball Joint Passenger Side

This part replaces:

  • OE # 5450041U02, 545002Y411, 545002Y412, 545006Y301
  • Hollander 512-58521R
  • Dorman 520-518
  • Moog K620354
  • OE # 54500-2Y412
Part #: 1ASLF00082


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:15 min)