This turn signal lever is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone for failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Controls the following functions:
    • Turn Signal
    • High Beam
    • Windshield Wipers with Delay
    • Windshield Wiper Washer
  • Black finish on handle
  • Replaces dealer part numbers: 3W1Z13K359BAB, 7W1Z13K359AA, 3W1Z-13K359-BAB, 7W1Z-13K359-AA, 3W1T-13K359-ABJAB0, 3W1T-13K359-ACJAB0, 3W1T-13K359-ADJAB0, 3W1T-13K359-ADJADR, 3W1T-13K359-AEJADR, 3W1T13K359ABJAB0, 3W1T13K359ACJAB0, 3W1T13K359ADJAB0, 3W1T13K359ADJADR, 3W1T13K359AEJADR, 4W1T-13K359-AB, 4W1T13K359AB, 5W1T-13K359-AA, 5W1T13K359AA, 7W1T-13K359-AA, 7W1T13K359AA, SW6226, SW6340
  • Exact replacement
  • Design improved for more durability
  • Detailed graphics
  • Built to strict quality control standards

This combination turn signal lever switch makes great replacement and has substantial cost savings over a dealer unit.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Disconnect the battery (1:03)
    • Use your 8 mm socket to disconnect the negative battery terminal
  2. step : Remove the wiper switch (1:14)
    • Turn your key to the run position and use a screwdriver to depress the button in the key lock cylinder to remove the lock cylinder.
    • Remove the tilt lever with an adjustable wrench
    • Remove the bottom trim panel by removing two 7 mm bolts.
    • Unbolt the five 10 mm bolts to remove that bracket.
    • Remove the steering column by removing the four Phillips screws.
    • Pry up the steering column covers.
    • Remove the three T20 Torx screws securing the switch.
    • Disconnect the wiring harness connections.
  3. step : Install the wiper switch (5:33)
    • Connect the wiring harness
    • Secure the switch by replacing the 3 T20 Torx screws.
    • Replace the steering column covers and secure them with the four Phillips screws.
    • Bolt the bracket back into place with your 10 mm socket and ratchet.
    • Re-install the bottom trim panel and secure it with your 7 mm socket and ratchet.
    • Replace the tilt lever and lock cylinder.
    • Line up the key and depress the tab to click it into place.
    • Shut the car off, reconnect the battery and test your switch.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 10mm Socket
  • 8mm Socket

  • Torx Drivers & Sockets

  • T20 Torx Driver

4.0 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
1
0
Crown Vic turn signal switch
The part arrived really quick. Price was about 1/3 of what other sellers were charging. Watched your installation video 3 or 4 times and was able to replace the defective switch in 45 minutes. Everything on the lever is working great. Really helps to know where and how to take things apart. I had a couple of minor differences, but otherwise, great video and part.
March 19, 2017
Purchased
1 year ago
DYI Saved me hundreds of dollars
The turn signal switch I found on line save me hundreds of dollars by doing it myself. The video that was provided made it simple with very little variations. Other than my ignition switch Tumblr was not quite as shown in the video, only because mine was somewhat different but was still easily removed with a little thinking. I was pleasantly surprised with the low price of the quality made part I ordered along with their customer service when I ran into a problem. I sent them pictures of the switch so they could see the situation and they contacted me back and discuss the matter with me. Come to find out it was my fall in overlooking a certain area. Also they warned me to be sure to disconnect the battery which I did. Success, the turn signal and wiper switch worked perfect. A good thing because the rain X on my windshield was starting to not quite work so well after two months without this part. Thank you 1AAuto.com
June 20, 2017
Purchased
1 year ago
Unsure
Installed this and the wipers don’t work unless on highest setting so at the moment not sure if it’s this part or something else
October 21, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2003-2011 Ford Crown Victoria Combination Switch for Models with Delay Wipers
  • 2003-2011 Lincoln Town Car Combination Switch for Models with Delay Wipers
  • 2003-2011 Mercury Grand Marquis Combination Switch for Models with Delay Wipers
  • 2003-2004 Mercury Marauder Combination Switch for Models with Delay Wipers

This part replaces:

  • OE # 7W1Z13K359AA
  • OE # 3W1Z13K359BAB
  • Hollander 629-00701, 629-00784
  • Standard Motor Products CBS-1188
Part #: 1AZTS00095

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(09:12 min)