This turn signal lever is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone for failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Controls the following functions:
    • Turn Signal
    • High Beam
    • Windshield Wipers with Delay
    • Windshield Wiper Washer
    • Hazard Switch
  • Black finish on handle
  • Exact replacement
  • Design improved for more durability
  • Detailed graphics
  • Built to strict quality control standards
  • Does NOT fit models with ESP (Electronic Stability Program) feature

This combination turn signal lever switch makes great replacement and has substantial cost savings over a dealer unit.

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Turn Signal and Wiper Switch (0:37)
    • Tilt up the lever on the bottom left of the steering column
    • Remove the three T20 Torx screws on the bottom of the steering column
    • Remove the T20 Torx screw at the back of the steering column lever
    • Remove the tilt steering column lever
    • Remove the gear selector cover
    • Remove the upper steering column panel
    • Remove the lower steering column panel
    • Insert the key into the RUN position without starting the vehicle
    • Turn the wheel about 9:00 until it rests
    • Remove the two Phillips head screws behind the steering wheel on the column
    • Push the safety tab on the multi-function switch and disconnect the wiring harness
    • Lift up the switch cover
    • Pull the switch out
  2. step : Installing the Turn Signal and Wiper Switch (3:10)
    • Snap the switch into place
    • Connect the multi-function switch
    • Tighten the two Phillips head screws behind the steering wheel on the column
    • Turn the key to the RUN position and check the functions
    • Insert the upper and lower steering column panels into place
    • Insert the tilt column lever into place
    • Tighten the T20 Torx screw to the tilt column lever
    • Tighten the three T20 Torx screws to the bottom of the steering column panels
    • Insert the gear selector boot into place

Tools needed for replacement:

    Screwdrivers & Related

  • Phillips Head Screwdriver

  • Torx Drivers & Sockets

  • T20 Torx Driver

4.6 / 5.0
29 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
23
2
2
1
1
Decent part for the money.
It does what it’s supposed to do but feels cheap. If an OE feel is important, spend the extra money and buy OE. If saving money is more important, this will do the trick.
June 17, 2018
Purchased
1 month ago
This product like all the products I've gotten from 1-A Auto.com is of superior quality. I look forward to doing business with you in the future. The price is affordable and backup videos are incredible. Thank you for let me write this review.
June 8, 2018
Purchased
2 months ago
Great Product
Looks good and works just like I expected. Thanks 1Aauto for a good product and the great price. I will order from you again.
June 5, 2018
Purchased
2 months ago
Combination switch
The swicth fit perfectly and was very easy to install
May 13, 2018
Purchased
5 months ago
Turn signal switch
Works great the installation video was okay but I got it in and it works fine.
May 10, 2018
Purchased
2 months ago
Combo Switch Doesn't Perform
Installed very easy. All the functions worked once. Then after one day of use, the intermittent wipers didn't work nor did the right hand turn signal turn off after a right turn. Now I am worse off than with what I had from the factory.
April 19, 2018
Purchased
4 months ago
Response from 1A Auto
Hello! I am sorry to hear that there is an issue with the part you purchased from us. If you need assistance please contact our customer service department. One of our representatives will be more than happy to help! - 1A Auto, 888-844-3393
April 19, 2018
Tim K Staff
Thanks
First let me say Thanks for the replacement part for my 2008 Dodge Ram Truck. Your video tutorial also made it very easy to replace. The Price for this part was why I made the purchased through your website. Very reasonable. I will recommend 1AAUTO to my friends and will continue to always check out your website for needed parts in the near future. Thanks Again George Esquivel, Lubbock Texas.
March 28, 2018
Purchased
4 months ago
Not as smooth as stock
I had this part on hand for a while before I could install it. I just installed it two days ago and I'm not very impressed with the quality. It hangs up really bad on right hand turns and needs to be manually rest at times. Not so mush on lefts but it's still very clunky. I'd spend a little extra on a Mopar part if you are planning to keep your vehicle.
February 24, 2018
Purchased
8 months ago
The part is good quality. The shipping was fast and ordering was simple.
February 7, 2018
Purchased
5 months ago
Perfect Fit!
All the local parts shops wanted twice this price for the entire turn signal assembly, and those require removal of the steering wheel. This part was very easy to replace without removing the wheel or messing with an air bag. The installation video was spot On! Thanks for the quality part and excellent customer service!
December 29, 2017
Purchased
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 5 answers
What brand of switch is this?
Ed Monkey on Jul 3, 2017
BEST ANSWER: We have a few different aftermarket companies build these parts specifically for us, as our 1A Auto house brand. They are manufactured to the same OEM specifications as the original part that came with your vehicle. If you have any further questions, please don't hesitate to ask.
Need multifunction turn signal switch for 2010 Dodge Ram 2500 with the ESP function. What part do I need? Do you have it?
Mary A on Jun 1, 2018

Vehicle Fit

  • 2007-2008 Chrysler Aspen Combination Switch for Models without Electronic Stability Program
  • 2005-2009 Dodge Dakota Combination Switch
  • 2004-2005 Dodge Durango Combination Switch
  • 2006-2008 Dodge Durango Combination Switch for Models without Electronic Stability Program
  • 2002-2006 Dodge Ram 1500 Truck Combination Switch
  • 2007-2008 Dodge Ram 1500 Truck Combination Switch for Models without Electronic Stability Program
  • 2003-2009 Dodge Ram 2500 Truck Combination Switch
  • 2003-2009 Dodge Ram 3500 Truck Combination Switch
  • 2007-2009 Dodge Sprinter Van Combination Switch
  • 2006-2008 Mitsubishi Raider Combination Switch

This part replaces:

  • OE # 56045515AA, 56049823AA
  • Hollander 629-00672L
  • Standard Motor Products CBS-1338
Part #: 1AZTS00093

How-to Video:

(05:52 min)