This combination wiper, headlight high beam dimmer, and turn signal switch lever is a new, aftermarket replacement part. It is designed to REPLACE original units that are prone to failure. It's just what you need to get your vehicle in good working order again!

Specifications:

  • Mounts to steering column
  • Direct replacement
  • Design improved for more durability
  • Detailed graphics
  • Built to strict quality control standards
  • Has rear wiper control

This combination lever is designed to replace your original with no modifications necessary.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Turn Signal Wiper Switch (0:40)
    • Remove the two 7mm bolts from the lower dash panel
    • Move the steering wheel up
    • Remove the lower dash panel
    • Remove the two Phillips screws under the steering wheel
    • Pull the lower steering column panel down
    • Remove the Phillips screw in the upper steering column panel
    • Remove the grommet around the ignition switch
    • Lift the upper panel up
    • Remove the 7/32 inch bolt from the upper part of the steering wheel
    • Push in the tab on the turn signal
    • Disconnect the turn signal switch wiring harnesses
    • Remove the turn signal wiper switch
  2. step : Installing the New Turn Signal Wiper Switch (3:23)
    • Insert the switch into place
    • Connect the turn signal switch wiring harnesses
    • Fit the grooves of the switch into place on the upper part of the steering wheel
    • Insert the top steering column panel into place
    • Insert the Phillips screw into the top steering column panel
    • Insert the lower steering wheel panel into place
    • Push the grommet over the ignition switch into place
    • Replace the two Phillips screws on the lower steering column panel
    • Push the lower dash panel into place
    • Insert the two 7mm bolts into the lower dash panel

Tools needed for replacement:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 5.5mm Socket
  • 7mm Socket

  • Sockets - SAE

  • 7/32 Inch Socket

4.1 / 5.0
17 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
10
1
3
3
0
Perfect
I used this item on our 2002 Ford Explorer. This item is built solid and works perfectly. I watched the install video and then went to work. The entire process took less than 10 minutes. Shipping was quick. The package shipped same day and arrived within three days. I will be ordering all of my parts from here.
March 26, 2016
Good price but it will not cancel itself on right turns. Tried to get another swapped out but no luck with customer service.
June 30, 2017
Purchased
11 months ago
Good enough
The best part was the detailed video of the installation. Part fit well, easy to install.

However, arm does not go back to regular position after a right turn. The arm clicks but does not move back.
June 21, 2017
Purchased
1 year ago
The Turn Signal had issue with clicking back after turn
All the functions of the switch work, except the return click once a turn has been made so that was an issue, however it is too much work to pull it out again and send it back so I am living with it. If anyone else buys it check to make sure that the switch returns to center position after the wheel turns and the turn is complete. I am just dealing with it right now.
January 25, 2017
Purchased
1 year ago
how completely incredible
i bought a turn signal lever two weeks ago for my son. He installed it. Did not tell me it would not turn off after a turn. I drove the car a week later to find this problem. Talked with a 1A rep. I was completely surprised. They are sending me a new part without the hassle of returning the bad part .
i will refer and be back for other parts. Thank you
April 3, 2017
Purchased
1 year ago
Very good service, especially the tutorial for the installation of the switch. 100% will recommend to friends and associates. Thank you.
July 6, 2017
Purchased
10 months ago
oturn signal
Same turn signal very good quality and same part as the original
March 1, 2017
Purchased
1 year ago
Replacement turn signal/wiper switch lever ‘04 Explorer
Nice perfect replacement for oem switch. A little stiff compared to old worn part but a solid part.
November 30, 2017
Purchased
1 year ago
Great price
For me to buy this piece at our local auto parts store was $100 more. I could not have been more pleased with the product. Only took about 15 minutes to install and I have had no problems with it.
March 30, 2017
Purchased
1 year ago
turn signal replacment
i ordered turn signal for 2004 ford explorer .perfect fit and great how too video.30 minute fix.
September 13, 2017
Purchased
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
My self canceling stopped working on the left turns, is that lever/cam part of this switch or is there another part on the steering column?
David M on Jan 2, 2016
BEST ANSWER: We had the same problem on my sons vehicle and replacing the turn signal lever switch did correct this issue for us. Hope this helps!
1AZTS00005-Combination Switch
1AZTS00005-Combination Switch

Vehicle Fit

  • 2003-2006 Ford Expedition Combination Switch
  • 2002-2005 Ford Explorer Combination Switch
  • 2002-2005 Mercury Mountaineer Combination Switch

This part replaces:

  • Hollander 629-00706
  • Hollander 629-00670
  • OE # 2L2Z13K359AAB, 1L2T13K359AGJAEA, 1L2TAGJAEA, SW5676, SW6072
  • Standard Motor Products CBS-1172
Only 3 left in stock
Part #: 1AZCC00176

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(06:13 min)