Replaces

Chrysler 300 Dodge Magnum Exterior Door Handle Front Pair - 1ADHS00800

These replacement exterior door handles are just what you need to get your vehicle in good looking form again!

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) or RH (Passenger Side) FRONT DOORS
  • Chrome Finish
  • Replaces dealer part numbers: 4589009AD, 4589009AH, 5065800AG, 5065800AH
  • Durable construction
  • Direct replacements
  • Built to strict quality control standards
  • Fit models with Keyless Entry only

These exterior door handles are great replacements and have good cost savings over dealer units.

Part Details

  • Color: Chrome
  • Front or Rear Location: Front
  • Quantity: Pair

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:58)
    • Pry out the trim piece inside the door handle
    • Remove the Phillips screw behind the handle
    • Remove the tan circle clips by pressing in the center and prying out the clip
    • Remove the four Phillips head screws on the bottom of the panel
    • Pry out the panel below the door pull
    • Pry out the door panel with a door panel clip tool or putty knife
    • Release the door handle cable by popping the clip, rotating the handle, and popping the hook out
    • Disconnect the window switch wiring harnesses
    • Pop out the wire harness retainers
    • Unplug the courtesy light and its wire retainers
    • Lift the door panel up and off
  2. step : Removing the Exterior Door Handle (3:22)
    • Disconnect the connectors on the door control module
    • Pry out the plastic clips on the module
    • Pry off the wire harness retainers
    • Pry off the adhesive on the weathershield
    • Release the lock and latch rod clips
    • Remove the two 8mm bolts from the door handle
    • Remove the door lock cylinder
    • Remove the door handle
  3. step : Installing the Door Handle (7:37)
    • Insert the door handle into the door, starting with the front
    • Tighten the 8mm screw to the door handle
    • Insert the door lock cylinder into the handle
    • Tighten the 8mm bolt to the cylinder
    • Connect the lock and latch rod clips
    • Connect the wire harness retainers
    • Press the module into the door
    • Connect the connectors to the module
  4. step : Installing the Door Panel (9:48)
    • Connect the courtesy light
    • Clip in the wire harness retainers
    • Connect the window switch wiring harnesses
    • Insert the latch rod into the door handle
    • Slide the clip over the latch rod
    • Lift the panel up over the door lock
    • Press the panel into place
    • Press the clips into the door panel
    • Tighten the four Phillips screws to the bottom of the panel
    • Tighten the Phillips screws beneath the door pull
    • Tighten the Phillips screw into the door handle
    • Press on the trim buttons

Tools needed for replacement:

    General Tools

  • Pick
  • Utility Knife

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

  • Specialty Tools

  • Trim Tool Set

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005-2010 Chrysler 300 Chrome Exterior Door Handle for Models with Keyless Entry Front Pair
  • 2005-2008 Dodge Magnum Chrome Exterior Door Handle for Models with Keyless Entry Front Pair
Part #: 1ADHS00800

How-to Video:

(11:49 min)