Replaces

Chrysler 300 Dodge Charger Shock Absorber - 1ASSP01542

Direct Fit

Direct fit replacement; not only will the part fit correctly, but it will function correctly.  Many competitors combine applications to cut down on the amount of parts they have to carry. This can result in the following issues: incorrect vehicle height, poor response and an uncomfortable ride.

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

Matched Parts

When you buy the kit pre-built by us, you can be sure that the parts are matched for optimum performance.  Not all shocks and struts are manufactured the same, so mixing and matching can result in fit issues and potentially decrease the life of the parts.

Saves Time & Money

When you buy one of our kits, you not only save money over buying the parts individually, but you also save time having to search for all of the different parts that are correct for your vehicle (because we did it for you!)

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:47)
    • Loosen the lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Rear Shock Absorber (1:56)
    • Remove the two 16mm bolts at the top of the shock absorber
    • Compress the shock
    • Pull out the top of the shock
    • Remove the bottom shock bolt with an 18mm wrench and a 15mm socket and ratchet
    • Pull out the shock
    • Hold the shock stud with vise grip pliers
    • Remove the 15mm nut from the top of the shock
    • Remove the shock mount from the shock
  3. step : Installing the Shock (4:46)
    • Remove the 15mm nut from the top of the new shock
    • Remove the washers from the new shock
    • Put the shock mount onto the new shock, with the rubber pointing out
    • Put the appropriate washer onto the shock stud
    • Fasten the 15mm nut onto the shock stud
    • Put the shock into place, top first
    • Compress the shock
    • Line up the shock with the lower control arm
    • Install the bottom shock bolt
    • Start the nut onto the bottom shock bolt
    • Fasten the bottom shock bolt with an 18mm wrench and a 15mm socket and ratchet
    • Tighten the bottom shock bolt to 53 foot-pounds of torque
    • Start the two 16mm bolts into the shock mount
    • Tighten the two 16mm bolts to 38 foot-pounds
  4. step : Installing the Wheel (6:40)
    • Put the wheel into place
    • Start the lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 110 foot-pounds in a crossing pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Gloves

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 21mm Socket
  • 15mm Socket

  • Wrenches - Metric

  • 16mm Wrench
  • 17mm Wrench
  • 15mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2011-2017 Chrysler 300 All Wheel Drive Front & Rear Shock Absorber 4 Piece Set without Nivomat Suspension
  • 2011-2016 Dodge Charger All Wheel Drive Front & Rear Shock Absorber 4 Piece Set without Nivomat Suspension

This part replaces:

  • Monroe 5797
  • KYB 349065
  • Monroe 72254
  • Monroe 72899
  • KYB 341673
Part #: 1ASSP01542


How-to Video:

(07:10 min)