Replaces

Chevy Impala Impala Limited Window Regulator - 1AWRG01077

Part Details

  • Regulator Option: with Motor
  • Operation: Power

This replacement power window regulator with motor is just what you need to get your vehicle in good shape again!

Specifications:

  • RH (Passenger Side) FRONT DOOR
  • Replaces dealer part numbers: 25890046, 20785173, 19180070
  • Power operation
  • Direct replacement
  • Includes power window motor
  • Built to strict quality control standards

This power window regulator with motor makes a great replacement and has good cost savings over a dealer unit.

Please Note:

This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. It has been subjected to extensive testing and quality control standards. That is why we offer this regulator with our superior warranty!

Direct Fit

Direct fit, pre-assembled parts made ready to fit your vehicle and provide easy and trouble-free installation.

Rigorously Tested

Build to strict quality standards

Highest Quality Materials

Made from the highest quality materials for extreme durability and premium performance.

Item Condition: New

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:55)
    • Pry off the trim piece inside the door pull with a flat blade screwdriver
    • Pry off the trim piece inside the door handle with a flat blade screwdriver
    • Pry off the reflector with a flat blade screwdriver
    • Remove the 8mm bolt inside the reflector
    • Remove the two T30 Torx screws inside the door pull
    • Remove the T30 Torx screw inside the door handle
    • Pry off the mirror base trim piece with a flat blade screwdriver
    • Pry out the door panel by hand
    • Lift the door panel up and off
    • Pinch the tabs on the cable housing with pliers
    • Remove the cable housing off the door handle
    • Pull the white lock back on the connector and remove the connector
    • Carefully peel off the water shield
  2. step : Removing the Window Regulator (2:42)
    • Remove the two 10mm bolts that hold the window to the regulator
    • Raise the window by hand
    • Hold the window in place with painter's tape
    • Disconnect the window motor lead
    • Remove the bottom left 10mm bolt on the regulator
    • Loosen the two 10mm bolts from the regulator
    • Loosen the three 10mm bolts from the window motor
    • Pull the window regulator out through the door
  3. step : Reinstalling the Regulator (4:35)
    • Switch over the bolts from the old regulator to the new one
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by its bolt
    • Insert the three 10mm bolts into the regulator
    • Insert the three 10mm bolts from the window motor
    • Connect the window motor lead
    • Wire tie the lead to the door and trim it with pliers
    • Remove the painter's tape from the window
    • Lower the window onto the regulator
    • Insert the two 10mm bolts into the window track
    • Reconnect the door switch harness and test the window
    • Disconnect the door switch harness
  4. step : Reinstalling the Door Panel (7:28)
    • Put the water shield into place
    • Lift the door panel into place
    • Reconnect the door switch harness and flip the white clip up and over to lock it
    • Connect the latch cables to the door handle
    • Push in the door panel to the window and clips
    • Insert the two T30 Torx screws inside the door pull
    • Insert the T30 Torx screw inside the door handle
    • Insert the 8mm bolt inside the reflector
    • Replace the reflector
    • Re-clip the mirror base trim piece
    • Re-clip the trim piece inside the door pull
    • Re-clip the trim piece inside the door handle

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Painter's Tape
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 8mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
Glad I found it on 1A Auto
Had I purchase the part from my local dealer or local auto store, I would have paid almost double. The part came within a few days and looked and worked as advertised. I most definitely will be ordering again when I need another part for my vehicles.
September 5, 2018
Purchased
1 month ago
Window regulator
Dealer wanted over $400. for material and labor. I Followed online instructions, take your time, works great.
January 14, 2018
Purchased
9 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2006-2013Chevy Impala Chevy Impala Front Power Window Regulator with Motor Passenger Side
2014-2016Chevy Impala Limited Chevy Impala Limited Front Power Window Regulator with Motor Passenger Side

This part replaces:

  • Hollander 125-00118R 617-00181R
  • Partslink GM1351157
  • Dorman 748-173
  • TYC 660199
  • OE # 25890046 20785173
Part #: 1AWRG01077


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:08 min)