2004 Chevrolet Silverado 3500 Driver Side Headlight Assembly Eagle Eyes GM269-B101L

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.

Hi, I'm Mike from 1A Auto. I hope this how to video helps you out and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to service the head lights. We're going to show you how to replace head lights if you want to buy a new set from 1A Auto. We'll also show you how to just change the bulbs if that's all you're looking to do. You may need to change your head lights if they're clouded or faded or cracked or chipped or damaged in any way. If they are damaged or you want to replace them, just go onto to 1AAuto.com and you'll find a new set of great head lights for your truck and we'll get you back on the road seeing clearly.

Open up the hood by pulling the lever here. Reach under the center of the hood. You'll see a little lever right here. Push it towards the center of the truck and lift up. Head lights are pretty easy. There's actually a little lock bar right here. Pull it up out of the clip. Then you might have to work it back and forth. You should pull it towards the center of the truck. This pulls right out and then your head light tilts back out. And right in behind, your head lights are connected. You don't have to have the battery disconnected. As long as the truck's off, there's no power going through here, just pull back on these tabs and push off the connectors, then your whole assembly comes out.

And if you're just looking to change the light bulbs, at this point, all you have to do is turn the light bulbs counter-clockwise, pull them out and put new ones in and then reconnect the bulbs and then go from there.

If you've had some damage or your lights are clouded or faded, the new light from 1A Auto is going to go in there, just like the original. It plugs in. The bulbs plug in, just like the originals. And on the bottom, there are 2 tabs that go in the slots here. You feed it in, behind the grill. Then peek back in there, until you can see those tabs going into their own spots. And once they're in, you can line it up right here, push it back in, put the pin in and through. If you just push it through, it locks down in place again. And as it's a new light, peel off the plastic.

We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.

One of the first things you need to do is pop your hood. Once you've done that, go ahead and grab onto this right here. Flip it up. Go ahead and draw it away. You might have to tilt it down to get it underneath there. Grab your headlamp assembly. Carefully pull it away. And then, if you were to look at the back, you're gonna see pigtails for the headlamps. Go ahead and grab that. Turn it counterclockwise. Carefully remove it. Do the same to the other one.

Now, it's gonna be time to install the headlamp. Go ahead and grab these bulbs. Start them. Line them up. Twist it. Lock it in. Do the same to the other. Okay. Now, we're just gonna come around the backside of the grille here just like this. Come up and over that. And then rest this right in. This should like up along there. And then, this should line up right down here. Now, we're gonna get our pin in here. It's a good idea just to clean it up if you can. Get off any of the rust that might be on it. Get it close to where I want it. Now, I'm just gonna bring the headlamp over. Squeeze this in. Bring it right on through. Line it up with this one. Flip this over.

All right. So now, it's gonna be time to test these lights. We got our headlights on. We got some high beams. Check that directional. Make sure it works. Perfect. We're sure that the lights all work. You'd want to just adjust the alignment of your headlamps. If you were to turn this to the left, it's gonna bring the beam up. If you turn it clockwise or to the right, it's gonna bring the beam down.

This is going to be a general tutorial on how to aim your brand new TRQ headlamp assemblies. Okay. So looking at your brand new TRQ headlamp assembly, you're gonna see where your low beam is, and you'll see a little dot right in the center, and that is the access point. Okay? So what we're gonna do is we're gonna mark that with an erasable marker just so it's easier to see. Next, what we need to do is measure from the level ground up to this point and take note of that measurement. Now, we're just gonna pull the car up to our wall. On our vehicle, we remember that the measurement was 28 inches for our access point. Your vehicle may be different, but that's where I'm going to put this tape. Just above that 28 inches. We'll do the same on the other side.

Okay. So let's just back the vehicle up, straight back, 25 feet from the wall. And now that we moved our vehicle 25 feet back from the wall, we're gonna start with our measurement here. That's where the headlamp center is. We're gonna go down 4 inches on the driver side. On the passenger side, we have our line here. What we need to do is go down 2 inches. To adjust the driver side, we're gonna cover our passenger side headlamp. If you look at the backside of your headlamp assembly, you're gonna see something that looks like this. This is the adjustment. Some of these headlight assemblies have one, two, or even more of them, but you should at least have one. This is how we're gonna adjust the headlight beam. Now, we're gonna lower the top part of the beam down to just below this line. When you turn the adjustment to the right it brings the beam up, and if you turn it to the left it'll bring the headlight beam down, and this is this way on most vehicles. Let's continue on to doing the passenger side. All right. We properly aligned our TRQ headlight assemblies. Okay. And on the quality TRQ headlamps for our pickup truck, the procedure's gonna be the same. You're gonna find your center dot, mark it, and then you'll measure from the level ground up to your dot.

So once your headlamps are properly adjusted, it'll be time to adjust your fog lamps. You'll notice on the driver side the focal point is all the way at the bottom right now. I would like to bring it up so it meets up with approximately the bottom of the focal point of the headlight. Some fog lamps have an adjuster, others don't. The ones that do have an adjuster, you would just turn the adjustment to the left or to the right to adjust the beam up and down to where it needs to be. Now with your TRQ headlamps and fog lamps properly aligned, you can drive down the road safely.