Replaces

Chevy GMC Hummer Front Wheel Bearing & Hub Assembly Timken SP580312 - TKSHF00188

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

TIMKEN WHEEL BEARING & HUB ASSEMBLY: SP580312

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 20835869
  • Fits 8 Lug Wheels
  • Direct replacement
  • Built to strict quality control standards

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (1:05)
    • Pry off the center cap with a flat blade screwdriver
    • Remove the hub nut cover with a hammer and chisel
    • Remove the hub nut with a 36mm socket and a breaker bar or a ratchet with pipe for leverage
    • Make sure the axle moves freely
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (2:05)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
    • Check for gouges on both sides of the rotor
  3. step : Removing the Brake Caliper and Pads (2:29)
    • Remove the two 19mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the brake pad slides
  4. step : Removing the Brake Caliper Bracket and Rotor (3:22)
    • Remove the two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the T30 Torx screw from the brake rotor
    • Pull the rotor off by hand
    • If the rotor will not come off by hand, apply penetrating oil to the studs
    • Tighten M10 bolts into the rotor to press it off
  5. step : Removing the Hub (4:35)
    • Apply penetrating oil to the hub bolts
    • Remove two of the three 15mm bolts from the hub mount
    • Loosen the third 15mm bolt
    • Use a hammer to loosen up the hub
    • Disconnect the ABS sensor wiring harness near the chassis
    • Remove the third 13mm bolt
    • Pull off the hub and backing plate
    • Disconnect the ABS sensor wiring harness at the hub
  6. step : Installing the New Hub (6:44)
    • Clean the steering knuckle with a wire brush
    • Apply white grease to the hub flange
    • Push the hub through the backing plate and on to the steering knuckle
    • Start the three 15mm bolts by hand
    • Tighten the 15mm bolts to 133 foot-pounds of torque
    • Route and reconnect the abs sensor wire at both ends
  7. step : Reinstalling the Brake Caliper Bracket and Rotor (8:25)
    • Slide the rotor into place
    • Thread one lug nut to hold the rotor in place
    • Put the brake caliper bracket into place
    • Start the 18mm bolts by hand
    • Tighten the 18mm bolts to 100 foot-pounds
  8. step : Reinstalling the Brake Caliper and Pads (9:06)
    • Apply white grease to the brake pads
    • Clean the rotor with brake parts cleaner or mineral spirits
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread bolts by hand
    • Tighten bolts to 50 foot-pounds
    • Remove the placeholder lug nut
  9. step : Reattaching the Wheel (11:00)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Put on the hub nut
    • Tighten the hub nut to 156 foot-pounds
    • Tighten the lug nuts to between 100-110 foot-pounds in a crossing or star pattern
    • Reattach the center cap, inserting the tongue into the wheel groove
  10. step : Testing the Brakes (11:36)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Chisel
  • Floor Jack
  • Hammer
  • Large C-Clamp

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • M10 x 7cm bolts
  • Mineral Spirits
  • Rust Penetrant
  • White Grease

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 36mm Socket

  • Star Drivers & Sockets

  • T30 Driver

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Best hubs for lifted Gm truck
Ive used several different hubs on my 2008 GMC 2500HD and hands down these are the best. They fit and feel just like the originals. They tend to cost a little more than others but its well worth it.
April 26, 2019
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007Chevy Silverado 2500 HD Chevy Silverado 2500 HD New Body Style Front Wheel Bearing & Hub Assembly
2008-2010Chevy Silverado 2500 HD Chevy Silverado 2500 HD Front Wheel Bearing & Hub Assembly
2007Chevy Silverado 3500 HD Chevy Silverado 3500 HD New Body Style without Heavy Duty Suspension Front Wheel Bearing & Hub Assembly
2008-2010Chevy Silverado 3500 HD Chevy Silverado 3500 HD without Heavy Duty Suspension Front Wheel Bearing & Hub Assembly
2007-2010Chevy Suburban 2500 Chevy Suburban 2500 Front Wheel Bearing & Hub Assembly
2007GMC Sierra 2500 HD GMC Sierra 2500 HD New Body Style Front Wheel Bearing & Hub Assembly
2008-2010GMC Sierra 2500 HD GMC Sierra 2500 HD Front Wheel Bearing & Hub Assembly
2007GMC Sierra 3500 HD GMC Sierra 3500 HD New Body Style without Heavy Duty Suspension Front Wheel Bearing & Hub Assembly
2008-2010GMC Sierra 3500 HD GMC Sierra 3500 HD without Heavy Duty Suspension Front Wheel Bearing & Hub Assembly
2007-2010GMC Yukon XL 2500 GMC Yukon XL 2500 Front Wheel Bearing & Hub Assembly
2008-2009Hummer H2 Hummer H2 Front Wheel Bearing & Hub Assembly
Only 4 left in stock
Part TKSHF00188
In Stock


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Timken
Brand #: SP580312