Chevrolet GMC Hummer Front & Rear Ceramic Brake Pads TRQ BFA12934

I'm going to use a 22-millimeter socket, take off the lug nuts, so we can remove the wheel. And remove the wheel. I'm going to take these two caliper slide bolts out. I'm going to use an 18-millimeter socket. Get those free first, and slide those out. Now, I'll take a screwdriver, I'm just going to pry the pistons of the caliper in a little bit, just go in between the caliper and the rotor, make it easier to take the caliper off. Now you can take a brake caliper hanger and support the brake caliper itself, just hook it on the upper control arm, or fold the caliper over and just set it so that it doesn't fall. Just make sure there's no tension on the brake hose.

Now we can take the brake pads off. Just use a straight blade screwdriver. Pry them off. Now, we want to take the caliper bracket off. We're going to take these two bolts out. I'm going to use an 18-millimeter socket, loosen those up. Take those bolts out and slide the bracket off. Take the rotor off. If your rotor is stuck on there, you can take a hammer and just hit in these areas. Just be careful of not hitting the studs. Slide it off. Just take a little anti seize, and just wipe it on the hub surface. Just a nice, thin coat.

Take the new rotor. Just going to put it on backwards, first. Take some brake parts cleaner. Just clean the back side of the rotor. Use a rag, wipe it off. And flip it over, and clean the front side, and wipe it down. If you want to, you can put a lug nut on to hold the rotor on. Makes installing it a little bit easier. Keeps the rotor in place. All right. Just take the brake caliper bracket. Use a screwdriver, straight blade screwdriver. Slide these anti rattle clips off where the pad slides off. Take a wire brush, just clean off the rust on this area.

All right. Now, just take some brake caliper grease, and just put a little bit on the ears, where the pad slides are going to go. Take the new pad slides, line them up, press them on. And take a little caliper grease, just put a nice thin coat right here, and right here, and do the same on the other side. And, just slide the caliper bracket over the rotor.

Take the bolts. You can put some thread lock adhesive on them. Now we're going to torque these bolts to 129 foot-pounds. Now, I'm going to take the brake pads, put the brake pads on. Now the warning indicator for the inboard pad, the one that goes on the inside, is going to be at the bottom. There's only one. There's nothing on the top. The one that goes on the outside has both squealers or warning indicators. Slide those into position.

Now, I need to compress the pistons back into the caliper. You can use a piston compressing tool. They make different types of tools. This is a ratchet type. As I tighten this up, it's going to push the brake fluid...push the piston back into the caliper, which is going to push the brake fluid through the hoses, through the lines, and back up into the master cylinder. Just go nice and slow. You don't want to rush this. The slower the better.
All right, those pistons are compressed. Now slide the caliper over the brake pads. Now you can take the two brake caliper bolts, clean them off with some brake parts cleaner, just wipe them off. These aren't too bad. And just take some brake caliper grease, on the guide pins. Now install the caliper bolts, or guide pins, and torque those to 80 foot-pounds.

Now you can take this lug nut off and put the wheel back up. Now put the tire back on. And the lug nuts. I'm going to torque the lug nuts to 140 foot-pounds in a star pattern or in a cross pattern, so that it tightens the wheel down evenly. Just go around again, double-check.

Now after you're done, you want to make sure you pump up the brake pedal, nice and slow. There's going to be an air gap between the caliper piston and the brake pads. So just do that, until that feels pretty good. And then double-check your brake fluid level, and adjust accordingly.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the brakes on this 2002 Chevy Suburban. The items you'll need for this include a new brake pad and rotor kit from 1AAuto.com, an 18mm and 22mm socket and ratchet, a piece of pipe for extra leverage, a T55 Torx bit, a large C-clamp, a torque wrench, a wire brush, jack and jack stands, brake cleaner, and brake grease.

You want to just loosen up these 22mm caps, and then pull the hubcap free. Then you want to loosen these lug nuts while the vehicle's on the ground, then raise the vehicle and remove them the rest of the way, unless you have air powered tools, then you can do it while it's in the air, and then just remove the wheel. You want to check for any deep groves in your rotor. You want to check in here for the life of your brake pads and over here for the life of the other one. You can see ours is actually in decent shape.

There's two T55 Torx bolts that you need to remove. We'll fast forward as we use a T55 Torx bit and a ratchet to remove those. Then, using a large C-clamp, just put it back behind the caliper here, and the other part right here on the brake pad, and just twist this in. This is going to push your caliper piston in and make it easier to pull the caliper off. Just remove the C-clamp and lift your caliper up and off and set it aside. Using a flat blade screwdriver, just pry out your brake pad. Sometimes the brake pads can be stuck in there. Use a flat blade screwdriver and a hammer to pry it free. You want to remove these two 18mm bolts on your caliper bracket.

You can see we use a piece of pipe for some extra leverage, here. We'll just fast forward as he breaks the other one free and removes both of these bolts. Now, slide the rotor off. On the left is the old rotor and brake pads, on the right are the new ones from 1A Auto. You can see they're identical and they'll fit exactly the same.

Spray your new rotor with brake cleaner and just wipe it down. Do the same thing to the back. Now, apply brake grease to the tabs on either end of your brake pads. Using your wire brush, just clean up those brake slides on your caliper bracket. Push your rotor back into place and then twist on a lug nut. This will hold the rotor in place. Turn the wheel and put the caliper bracket back in to place. Replace those two 18mm bolts. We'll fast forward as Don does this and tightens both of those up. Torque both of these to 75 foot-pounds.

Push your new brake pads into place. Use a hammer if necessary to lightly tap that into place. Using an old brake pad, just put it onto the caliper pistons and then tighten it in with your C-clamp. This will just push those pistons in the rest of the way. Grease up your caliper bolts. Out the caliper back into place and slide those slide bolts back in. We'll just fast forward as Don tightens those up. You'll want to tighten these to about 30 foot-pounds.

Now, replace your wheel and then replace those lug nuts and tighten them preliminarily, lower the vehicle, and tighten them the rest of the way. Torque the lug nuts in a crossing pattern to 100 foot-pounds. Replace the hubcap and tighten up those caps. After doing work on your brakes, you want to pump the brake pedal until it firms up and then try a stop test from five miles per hour and ten miles per hour, and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.