Chevrolet Pontiac Saturn Front 10 Piece Steering & Suspension Kit TRQ PSA58970

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a stabilizer link on this Chevy Cobalt, pretty much the same for any Cobalt as well as the Pontiac G5. The stabilizer link makes kind of a rattling or thunking noise when you go over a bump. A good indicator that it's your stabilizer link is if you're getting that rattling noise and then, you turn your vehicle, you take a curve, and the rattling noise goes away; that usually means it's a pretty good indicator that it's that stabilizer link that's bad. The tools you'll need are jack and jack stands, 18mm and 19mm sockets with a ratchet. You'll need some pipe for some extra leverage as well as a breaker bar and 15mm and 18mm wrenches. It's pretty much a bolt-on, bolt-off, but sometimes these nuts are really difficult to remove, so there's some techniques in this video that will help you out.

Use a 19mm socket or lug wrench and remove the lug caps and the wheel cover. If you don't have access to air tools, you'll want to start with the vehicle on the ground. Loosen the lug nuts first and then raise the vehicle and remove the lug nuts and the wheel and tire.

Now, use an 18mm wrench and you can grab on the back side there and then use an 18mm socket and ratchet and remove that nut. Use a little bit of penetrating oil just to help get that nut off easier. Now, I'm using my 18mm socket with the ratchet and a piece of pipe. You can use pipe or if you have a breaker bar. You just need some extra leverage. Get that bolt to move some, and then, actually, grab on to the wrench, hold the wrench, and start it loosened and then you can do it by hand the rest of the way. Once you remove that nut, then you can just knock out or remove the top of that stabilizer link. Now, here what I've done is I've supported the bottom of the suspension. What that allows, is it allows me to get a breaker bar onto that bottom bolt and first you can pull the breaker bar, which breaks the nut and the bolt, breaks it free. Then you see with the breaker bar, I start loosening up that nut. You're just going to have to work at it, it's kind of tough to get apart. Just go at it for a while and the nut eventually comes off. Actually, after you get it loosened somewhat, you can get your ratchet on there, and then, use the ratchet to get the nut the rest of the way off. Once you have that off, you can just reach up in there and pull the stabilizer link out.

So, the 1A strut is pretty much the same thing. It has a little different sizes. It's a 19mm nut and a 15mm stud. We'll fast forward through this part. You just take that stabilizer link and put it back into the new strut and put the nut on, and tighten the nut up. You want to get it nice and tight. If you were to torque it, I guess it would be probably about 45 to 50 foot-pounds. Also, if you have ABS brakes, you want to reconnect any clips or anything that holds the wiring to the strut.

Reinstall the tire. You want to put the lug nuts on by hand first and then just kind of preliminarily tighten them, and torque them when the vehicle is back down on the ground.

We'll tighten and torque these to 20 foot-pounds. We'll speed up here as I do that. On the inside one you can't really get a torque wrench on it, so I just used a small combination wrench and got it nice and tight. 20 foot-pounds is not that tight. You don't want to over-tighten them because you could strip them and these are not bolts that you want to strip. Now torque your lug nuts to 100 foot pounds each and then replace either your wheel cover or the wheel caps and the retainers

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace an outer tire rod on this 2007 Pontiac G6. It's pretty much the same as any 2005 to 2010 G6, as well as a Saturn Aura. We show you the right-hand or passenger side, but the left-hand driver side is the same procedure. You'll need a new tie rod or tie rods from www.1AAuto.com, jack and jack stands, 18mm and 19mm sockets with a socket wrench, maybe even a breaker bar or a pipe for leverage, tape measure, 18mm wrench, large adjustable or a 13/16 wrench, hammer, and a torque wrench.

Depending on what wheels you have, start out be removing the lug caps, and then we'll cover if applicable. Then, if you don't have the benefit of air tools, you're going to want to loosen the lug nuts with the vehicle on the ground. Then raise and support the vehicle. I'll remove the lug nuts, wheel, and tire.

Use a tape measure to get a general idea of a total length. You can use a reference point of the outer part of the boot, and then the outer part of the tie rod end, and just remember that number. On the end of the tie rod is an 18mm, so I'm using the socket and socket wrench to remove that nut. I'll fast-forward as I take off that nut.

Locate the nut at the end of the outer tire rod. We're going to go ahead and just loosen it just a little bit. I'm using a 13/16 wrench. You can use the metric equivalent. With a hammer, go ahead and give the end of that spindle a whack and pull the outer tie rod out. Then you can go ahead and unscrew it. I'll fast-forward through that. Be as careful as you can to not turn the inner tie rod.

Here, we're going to reinstall. You'll notice we are reinstalling the old one. There's nothing wrong with the tie rods on this vehicle. We just are doing this to show you how to do it. Tie rods from 1A Auto are going to be an exact match to the original. You may want to just measure the length. There could be a slight difference in length, and you would want to make sure you align it well.

Go ahead and put that 18mm nut back on the outer tire rod. I'm using a small pair of vice grips to hold the other part of the ball joint so that it doesn't spin as I tighten up that 18mm nut. There might be other ways that you would find easier to do it, but that's the one that I use. Then once I get it through, I'll be able to put the vice grip on the end that's coming through the nut. You can see here that once I take that socket off, I'll have plenty of room to put that on, and then use an open-ended wrench.

Here, I'm using that vice grip on the bottom, and I'm going to use an open-ended wrench to finish up tightening it up. I'll fast-forward through this. Now tighten up the nut on the inner tie rod that we just slightly loosened. Make sure that's snug up against the back portion of that outer tie rod. I'm just verifying that the tire rod is in somewhat of a right position, and it will be ready for me to take over to have an alignment done.

Install the wheel, and tighten up on your lug nuts. I'll go ahead and fast-forward through this. In a star pattern, go ahead and torque your lug nuts to roughly 100 foot-pounds. Reinstall your hubcap, and make sure that you line up the notch in the hubcap for where your valve stem is. Then, by hand, use your 19mm socket to tighten up those plastic lug nut covers. I'll fast-forward through that.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Okay, friends, before we get started, the first thing that I want to mention is you wanna be safe. So have hand protection and eye protection. The next thing we're gonna talk about is safely raising and supporting the vehicle so the suspension's hanging. So come right underneath here. This is where you're gonna support the vehicle in the front. Now, with the front of the vehicle safely raised and supported, we're gonna remove all five of our 19-millimeter lug nuts. Remove your wheel.

Now that we have the wheel off, we have a clear view of our tie rod area. I'm just gonna spray down these areas with some penetrant spray. Now we're gonna use some nice long pliers, and I'm gonna break this jam nut free. Turn this clockwise. There we are. Now we're gonna remove our outer tie rod end nut. If you find that the outer tie rod end nut just spins the whole stud inside of the knuckle, you could take those nice long pliers or whatever you might happen to have and just try to squeeze this down as tight as you can. We're gonna apply a little bit of pressure and we'll try again. If your tie rod's still stuck in the knuckle, it's great to use a hammer, bonk right on the knuckle right here and break it free.

For the next part, we're gonna want something that you can write with because we're gonna take off the tie rod, but as we turn it and we make a complete rotation, we're gonna count those rotations and take note of it. That's one, two, three, and so on. The next thing we need to do is hold our inner tie rod end shaft with some locking pliers. After that, we're gonna remove this jam nut. Next, we need to remove this clamp right here. I like to use some nice long pliers.

Next, we need to remove this metal clamp right here. To do that, it's easiest if you bonk on it with something. I'm just gonna use a pry bar and a hammer. I'm gonna bonk it, break it free, and we'll get that boot right off. Here it is. Grab onto your boot. Give it a nice little twist. See if you can break it free from the power steering rack. If your boot is stuck on the power steering rack, you can be careful and use an ice pick like this and just try to break it free. Oh, yeah. Now I can give it a nice twist. Pull it off the power steering rack. You might notice it's also stuck on here. If you want to use a tiny bit of penetrant, you could do that. I'm just gonna twist and give it a tug. It should wanna slide right off.

Next, it's gonna be time to get the inner tie rod end off of the power steering rack. A wise man once said whatever works, works. So you can either use some nice long pliers like this, an inner tie rod end tool that looks like this, or they even have a tube that would slide over with a little adapter. Do whatever you need to do, but turn it counterclockwise and remove it from the rack. Now that the tool's on there, let's go ahead and break this free. There we are. We'll just get our tool off of there, but there it is.

Now it's gonna be time to install our brand new inner tie rod end. One thing that you wanna do, of course, is to take off that jam nut. We're gonna be reusing it, so we'll just set it aside. After we've done that, we're gonna apply a little bit of grease, right along inside here of the nice packet that they gave us. Don't use it all because we're also gonna use a little bit right along this lip right here. I'll just put all this right in there. Using a gloved finger, go ahead and just smooch it all right in there. This is gonna help keep moisture out of there and, of course, help lubricate it over time. A little bit right here, like I said. If you wanna use a little bit of blue threadlocker on those threads, we'll call it your prerogative. I'm just gonna go ahead and screw this on here until it's nice and snug and then we'll tighten it to manufacturer specifications. Torque this to 74-foot-pounds.
Now it's gonna be time to get our inner tie rod end boot on there. Just go ahead and take a nice wire tie, start it so it's not tight yet. We're gonna slide this right on over. We'll put it over the rack as well, and then, of course, we'll snug it right up. You need to make sure you have some sort of clamp if you don't use a wire tie. Trim off the excess. Now we're gonna make sure we put on the outer clamp. If it's damaged or it doesn't seem like it has enough spring retention, of course, replace that with something as well. Now it's gonna be time to coat the threads with something. If you don't have any copper never seize, you can go ahead and just use a tiny bit of that grease that we just used for the inner tie rod end. New jam nut.

Now it's gonna be time to put on our brand new outer tie rod end. As you go to install it, make sure you put on the same amount of turns that you had to remove the old one. One, two, three, and so on. Should pretty much line up. Let's put on our outer tie rod end nut. We'll snug it up and then we'll torque it to manufacturer specifications as well. We wanna torque this to 18-foot-pounds and then add an additional 90 degrees. So basically 1/4 turn after the 18. So that's 18. Now I need to take it another 1/4 turn. I'm gonna start approximately like that and I'm gonna bring it right out to me. There we are.

The next thing we wanna do is pay attention to the slots on the nut, compare it to the hole in the stud. If it doesn't line up, you need to continue tightening until it does. Go to the very next slot. As you can tell, I have that lined up now. Take your cotter pin, slide it through, and then peen it over so there's no way this nut can loosen up on its own.

Now it's time to tighten up our jam nut. We're gonna grab this, turn it counterclockwise. That feels good. Now just go ahead and grab onto that tie rod, make sure it's pretty level and it's not kinked in any way. Double-check everything. We have all our clamps. Perfect. We're gonna go ahead and put the wheel on here. We'll start all the lug nuts. We'll snug them up and then we'll torque them to 100-foot-pounds. Torqued.

Okay friends. Before we get started, the first thing that I want to mention is you want to be safe, so have hand protection and eye protection. The next thing we're gonna talk about is safely raising and supporting the vehicle so the suspension is hanging. So come right underneath here, this is where you're gonna support the vehicle in the front. Now with the front of the vehicle, safely raised and supported. We're gonna remove all five of our 19-millimeter lug nuts.

Remove your wheel. Now that we have the wheel off, we have a clear view of our tie rod area, I'm just gonna spray down these areas with some penetrant spray. Now we're gonna use some nice long pliers, and I'm gonna break this jam nut free. Turn this clockwise. There we are. Now, we're gonna remove our outer tie rod end nut.

If you find that the outer tie rod end nut just spins the whole stud inside of the knuckle, you could take those nice long pliers or whatever you might happen to have, and just try to squeeze this down as tight as you can. We're gonna apply a little bit of pressure, and we'll try again. If your tie rod still stuck in the knuckle, it's great to use a hammer, bonk right on the knuckle right here, and break it free.

For the next part, we're gonna want something that you can write with, because we're gonna take off the tie rod, but as we turn it, and we make a complete rotation, we're gonna count those rotations and take note of it. That's one, two, three, and so on. It's always important to make sure you coat your threads with something such as copper never seize.

Now it's gonna be time to put on our brand new outer tie rod end. As you go to install it, make sure you put on the same amount of turns that you had to remove the old one. One, two, three, and so on. Should pretty much line up. Let's put on our outer tie rod end nut. We'll snug it up, and then we'll torque it to manufacturer specifications as well. We wanna torque this to 18 foot-pounds and then add an additional 90 degrees, so basically a quarter turn after the 18. So that's 18. Now I need to take it another quarter turn. I'm gonna start approximately like that, and I'm gonna bring it right out to me. There we are.

The next thing we wanna do is pay attention to the slots on the nut compared to the hole in the stud. If it doesn't line up, you need to continue tightening until it does. Go to the very next slot. As you can tell I have that lined up now. Take your cotter pin, slide it through, and then peen it over so there's no way this nut can loosen up on its own.

Now it's time to tighten up our jam nut. We're gonna grab this, turn it counterclockwise. That feels good. Now just go ahead and grab onto that tie rod, make sure it's pretty level and it's not kinked in any way. Double check everything. We have all our clamps. Perfect. We're gonna go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up, and then we'll torque them to 100 foot pounds. Torqued.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a front stabilizer link on this 2007 Pontiac G6. It's the same as any 2005 to 2010 G6, as well as the Saturn Aura. Not a difficult procedure. You will need jack and jack stands, and you'll want to jack up both front wheels off the ground and support it with jack stands. Then you'll need a lug wrench or a 19mm socket with a ratchet, maybe even a breaker bar and a pipe for some extra leverage. Then, after that, you'll just need two 18mm wrenches, one of those 18mm will have to have an open end.

Start out by using just a socket to loosen the lug nut covers, or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools, just start with the vehicle on the ground, loosen the lug nuts, then raise and secure the vehicle, and move the lug nuts from the wheel and tire.

Use an 18mm wrench to grab on to the nuts, part of the stud of the stabilizer link, and then use an 18mm socket, loosen up the nut, and then it comes off. Here's the fun part of the repair. You pull that down out of the way, and you can see the other end of the link right there. Put the 18mm wrench on the nut that's in the shaft, just like before. Then, there's not really enough room to get a ratchet back in there, so you basically just have to take a wrench and slowly, carefully, one eighth of a turn at a time, and I'll fast-forward the video as we do that.

Then, just reinstall the link as you took it apart. Go ahead and speed up as we tighten up that lower nut, and like I said before: it's not all that difficult; it just takes quite a bit of time because you can't move that nut too far each time.

Bring the sway bar link back into place, and should you possibly feel the need to replace those sway bar links, at 1AAuto.com, we sell those as well. But then use a 18mm wrench and an 18mm socket and ratchet to tighten up that bolt. And that bolt should be tightened somewhere around 70 to 75 foot-pounds. Put the bracket that holds your brake hose back into place, and start the 10mm bolt on and tighten it up.

Reinstall the wheel. Put the lug nuts on by hand first just to make sure you don't cross thread them, then tighten them preliminarily. Put the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now, reinstall your hubcap and we're going to do that with that 19mm socket. I'm just going to screw them in by hand. Also, we want to make sure you line up the valve stem with the notch in the hubcap for the valve stem. I'll go ahead and fast-forward through that.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Now, with the front of the vehicle safely raised and supported, we're gonna remove all five of our 19-millimeter lug nuts. Remove your wheel. Now that we have the wheel off, I always like to put just one lug nut back on just to hold the rotor from flopping around. We have a nice, clear view of our lower control arm at this point, we're going to be removing this bolt right here. Up above that, you're going to see two nuts that have bolts that come through from the bottom. We're going to spray those two nuts as well. And then if you were to follow the control arm all the way over to the knuckle, you're going to see that there's a pinch bolt that goes through right there. And, of course, a slot on the knuckle where the ball joint goes through. Let's spray all those areas as well. The next thing I like to do is remove the pinch bolt for the ball joint. I'm gonna use my 15-millimeter here to take off the nut and hold the bolt with a 16-millimeter. I might need to use a punch and a hammer to get this out of here. I'm gonna respray this area with more penetrant and let it sit and do its job. Let's move along. Next, let's remove this bolt right here using our 14-millimeter wrench. Let's remove the forward bolt. Let's just leave this bolt in just a tiny bit. Let's get our wrench onto these top nuts up there and remove the bolts from the bottom.

Now we need to separate our ball joint from the knuckle itself. To do that, I'm going to bonk right along here with my hammer and just try to separate the two. You could also use a pickle fork, come right in between here. Or if you had to, you could try to spread the knuckle a little bit using a punch. As you can tell, it's starting to separate. Let's continue. Sometimes a pry bar will come in handy. Let's remove our forward bolt, tilt this down some more. Continue with the pry bar. Draw this out of here. Grab the control arm, pull it towards the front of the vehicle. Let's get the rearward bracket out of here. There it is, friends. The next thing I like to do is mark the control arm with the rearward bushing, so I know how they need to line up. And then we're going to remove this bolt right here using our 14-millimeter wrench. There we are. Take this right off of here. Set it aside. Next. I like to apply thread locker to all my bolts that I'm going to be reinstalling. Now we're going to loosely install our rearward bushing here. You want to make sure that you have this portion facing towards the front and not this portion. My bolt, there it is. Next, I like to apply a little bit of grease or lubricant along the shaft area right here. It's going to help it slide into that bushing. And just a tad up along the ball joint stud here, let's go ahead and put this up in here like this. Put it through that rear bushing.

Now we're just gonna swing this up. We're going to try to line our ball joint up with the knuckle right there. There we are. Carefully using a rubber mallet. Start the bolt through there, pin that on there. Now we need to do the forward bushing. Slide that like that so it's lined up. Now we're going to carefully bonk under here with a rubber mallet and try to line up the forward hole. Start this in. This other bolt started in here as well. At this point, we're going to snug these two up. Put some thread locker on this bolt and put this in there. We're going to bottom it out. Let's carefully bottom this out. Now we're gonna torque this. You want to torque it to 37, loosen it up a little bit, re-torque it to 37, and then we're going to go an additional 30 degrees. Okay. So, there's 37, now we're just going to go our approximate additional 30 degrees. Now we're gonna tighten these bolts to 37 foot-pounds, and then we'll also tighten them an additional 90 degrees afterward. So, I'm gonna turn this just like this, and now I'll bring the ratchet pretty much straight back to me. There we are. Do the same to the other one.

Next, we need to apply load to the suspension so it would be as though the vehicle's wheel is on the ground and the weight of the vehicle's on it. That's it right there. Once you've done that, let's go ahead and bottom out this bolt right here. Now we're going to torque this bolt to 37 foot-pounds. And then after we've done that, we need to continue an extra 90 degrees. There we are. The next thing we need to do is snug this up right here, and then torque it to 32 foot-pounds. Let's unload the suspension. Let's get this lug nut off of here. Put the wheel back on, start all the lug nuts, bottom them out, and then torque them to 100 foot-pounds.

Okay, friends. Before we get started, the first thing that I want to mention is you want to be safe. So, have hand protection and eye protection. The next thing we're going to talk about is safely raising and supporting the vehicle so the suspension is hanging. So, come right underneath here. This is where you're going to support the vehicle in the front. Now, with the front of the vehicle safely raised and supported, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel.

First, what I like to do is remove the sway bar link from the front strut. So, I'm going to use some locking pliers, come from the backside right here and just try to hold onto the stud so it can't spin. All right. Let's get this off of here. Okay. Now that we have the sway bar link off of here, we need to go over to the other side of the vehicle and remove the sway bar link from the strut as well. That way there, we can move the sway bar up and down as needed to get to that mounting nut. There it is, friends.

Okay, friends. Now it's going to be time to put it in our brand new front sway bar link. One thing I like to mention is it's always a great idea to do these as a pair. And if that's the case, now's the time to do it. So, let's go ahead and put this in starting with the bottom. Now, I'm going to use my 17-millimeter wrench to hold the stud from spinning, and then we'll snug it up. If you were to try to torque this you'd want to torque it to 48 foot-pounds. It's going to be very difficult to torque because as you try to twist, it's going to want to lift up on the bar. If you try to put the bar inside here, obviously, you're not gonna be able to get to it. So, 48 foot-pounds, if you can do it. Let's get the sway bar link connected to the strut. Let's torque this to 48 foot-pounds. We're going to go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up and then we'll torque them to 100 foot-pounds. Torqued.