Chevrolet GMC Cadillac Rear Ceramic Brake Pads TRQ BFA73067

I'm gonna take the center cap off. Use a straight blade screwdriver to get that off. Use a 22-millimeter socket, take off the lug nuts. Take the wheel off. Take these two caliper bolts out. I'm gonna use a 12-millimeter socket and then a 16-millimeter wrench just to hold the slide from spinning. Loosen these up. Now, just use a screwdriver, pry the caliper off. Pull it out. Then you can use a caliper hanger and just support it from the upper control arm right there. Just make sure there's no tension on the hose. Slide it over here. Take the brake pads off. Just use the same straight blade screwdriver. And take an 18-millimeter socket, take these 2 caliper bracket bolts up. Take these bolts out and slide the bracket right off. Now, take the rotor off. If it's stuck on there, just take a hammer, give it a tap in these areas. Just try not to hit the studs. Keep it loose. Try not to breathe any of that in and slide it off. I'm just gonna clean up this surface right here. You can use a wire brush or some type of grinding wheel. Just be careful, you don't wanna take too much material off. Just get some of the rust off. Take a little anti-seize, just put it on the hub area right here. Now, we're just gonna put the rotor on backwards first and we're gonna clean off the surface. Use a little brake parts cleaner. There is a protective coating on this, clean that up. You can clean up the inside of the drum area as well for the parking brake. Flip that around and clean off this area as well.

When you go to put the rotor on, you may have to adjust the parking brake. You can spin that wheel either forward or backward and...or you can either tighten it or loosen it. Just slide the rotor on just to make sure it spins good. And then double-check with your parking brake and adjust accordingly. Now, take these pad clips off or pad slides or sometimes they call them anti-rattle clips. Just use a straight blade screwdriver. Use a wire brush, clean up any rust built up, right here, and on the other side. With that cleaned up, and then just take a little brake caliper grease, give it a nice thin coat. It's gonna keep the moisture out, keep it from rusting as bad as it was. Then take these clips and slide it in position. Put more caliper grease, just a nice thin coat there and there, wherever the pads are gonna contact it. And then do the same on this side. I'm gonna take these caliper guide pins out. Use a little brake parts cleaner and a rag, clean these up. And I'll also spray a little brake parts cleaner down there. Clean those up with a rag as well. You can drain anything out. And take some brake caliper grease, coat the pin, put it back in. Make sure it seals, and do the same on this one. Slide the brake caliper bracket in place, put the bolts in. You can use a little thread locking compound on the bolts. Now, I'm gonna torque these bolts to 122 foot-pounds.

Now, I'm gonna install the brake pads. Make sure you have the brake pad warning indicator facing up on the outside and also on the inside. Now, take the brake caliper off, take the hanger off. Now, I have to compress the caliper, so use a brake caliper compressing tool. Just compress it really slow. This is gonna push the fluid through the hoses, back through the lines, back up to the master cylinder, and into the reservoir. Just go nice and slow. All right, if that's compressed, pull the compressing tool out. Now, we have a new little bracket right here. It comes with the brake kit. Just take a straight blade screwdriver, this little tab right here, just push in on that tab. Slide that off, take the new one, slide it in there, and then just push it, lock it in place. So, that's in there just like that. This is just gonna push down on the pads and just keep them from rattling around. Slide the caliper over the brake pads in the bracket. Take the two bolts, install the bolts. You can put some thread locking compound on those bolts, and then use my 16-millimeter wrench, 12-millimeter socket, torque these bolts to 31 foot-pounds. And reinstall the wheel, put the lug nuts on. Now, I'm gonna torque these lug nuts to 140 foot-pounds in a star pattern to tighten the wheel down evenly. Then just go around again, double-check. And then reinstall the center cap. Now, I'm gonna pump the brake pedal nice and slow. There's gonna be an air gap between the caliper piston and the brake pad, so we wanna eliminate that air gap. And once the pedal feels good, then you're all set. Check the brake fluid level in the master cylinder reservoir. There's the minimum line right there and the max line right there, adjust accordingly.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the brakes on this 2002 Chevy Suburban. The items you'll need for this include a new brake pad and rotor kit from 1AAuto.com, an 18mm and 22mm socket and ratchet, a piece of pipe for extra leverage, a T55 Torx bit, a large C-clamp, a torque wrench, a wire brush, jack and jack stands, brake cleaner, and brake grease.

You want to just loosen up these 22mm caps, and then pull the hubcap free. Then you want to loosen these lug nuts while the vehicle's on the ground, then raise the vehicle and remove them the rest of the way, unless you have air powered tools, then you can do it while it's in the air, and then just remove the wheel. You want to check for any deep groves in your rotor. You want to check in here for the life of your brake pads and over here for the life of the other one. You can see ours is actually in decent shape.

There's two T55 Torx bolts that you need to remove. We'll fast forward as we use a T55 Torx bit and a ratchet to remove those. Then, using a large C-clamp, just put it back behind the caliper here, and the other part right here on the brake pad, and just twist this in. This is going to push your caliper piston in and make it easier to pull the caliper off. Just remove the C-clamp and lift your caliper up and off and set it aside. Using a flat blade screwdriver, just pry out your brake pad. Sometimes the brake pads can be stuck in there. Use a flat blade screwdriver and a hammer to pry it free. You want to remove these two 18mm bolts on your caliper bracket.

You can see we use a piece of pipe for some extra leverage, here. We'll just fast forward as he breaks the other one free and removes both of these bolts. Now, slide the rotor off. On the left is the old rotor and brake pads, on the right are the new ones from 1A Auto. You can see they're identical and they'll fit exactly the same.

Spray your new rotor with brake cleaner and just wipe it down. Do the same thing to the back. Now, apply brake grease to the tabs on either end of your brake pads. Using your wire brush, just clean up those brake slides on your caliper bracket. Push your rotor back into place and then twist on a lug nut. This will hold the rotor in place. Turn the wheel and put the caliper bracket back in to place. Replace those two 18mm bolts. We'll fast forward as Don does this and tightens both of those up. Torque both of these to 75 foot-pounds.

Push your new brake pads into place. Use a hammer if necessary to lightly tap that into place. Using an old brake pad, just put it onto the caliper pistons and then tighten it in with your C-clamp. This will just push those pistons in the rest of the way. Grease up your caliper bolts. Out the caliper back into place and slide those slide bolts back in. We'll just fast forward as Don tightens those up. You'll want to tighten these to about 30 foot-pounds.

Now, replace your wheel and then replace those lug nuts and tighten them preliminarily, lower the vehicle, and tighten them the rest of the way. Torque the lug nuts in a crossing pattern to 100 foot-pounds. Replace the hubcap and tighten up those caps. After doing work on your brakes, you want to pump the brake pedal until it firms up and then try a stop test from five miles per hour and ten miles per hour, and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the rear brake pads on this 2002 Chevy Suburban. We show you on the passenger side, but the driver's side is the same procedure. The items you'll need are new brake pads from 1AAuto.com, 12 and 22 mm socket and ratchet, flat blade screwdriver, large C-clamp, torque wrench, and jack and jack stands.

Start off by loosening up these lug nut covers and we'll fast forward as Don does this. Once those are all loosened up, you can pull the hubcap free. Now, you want to loosen the lug nuts preliminarily, raise the vehicle, and remove them the rest of the way, unless you have air powered tools. Then, you can do it while it's up in the air.

To inspect your brakes, run your finger along the rotor, check for any deep grooves. You can look in here for the life of this brake pad, and then, through here for the life of the other brake pad.

Now, remove these two 12mm bolts and we'll fast forward as Don does that. Use a large C-clamp. You put it on this end on the back of the caliper and on this brake pad and just twist it in. This is going to push the caliper piston in and make it easier to pull the caliper up and off. Remove the large C-clamp, pull the caliper free, and set it aside. Pry out the brake pads.

Take your new brake pads and apply brake grease to the tabs on either end of the brake pads. You want to reset the pistons in your caliper so put an old brake pad in there and just twist the C-clamp and it'll push those pistons back in. Push your new brake pads into place, and then, put your caliper back down into place and replace those two 12 mm bolts. We'll fast forward as Don does this and tightens them up. You want to tighten these to about 30 foot-pounds.

Put your wheel back into place and then replace your lug nuts and tighten them preliminarily. We'll fast forward as Don does this. Lower the vehicle and torque the lug nuts to 100 foot-pounds in a crossing pattern. Replace that hubcap and tighten up each of your lug nut covers. Before taking the vehicle out on the road you want to pump the brake pedal until it firms up and then do a stopping test from 5 miles per hour and then 10 miles per hour and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.