Replaces
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we'll be installing a tailgate cable on a 2004 GMC Sierra. It's basically the same as any GMC Sierra or Silverado from 1999 to 2006. The only tool you'll need is a 1/2 inch wrench.
Open up the tailgate. You got a bolt here. It's a ½ inch bolt. Remove that. If it's frayed, you can replace it. Not a difficult thing to replace at all. Most people can do it. If you're wondering how, that's how. A couple of keys, make sure if you're replacing one, the other one's in good shape. You don't want the tail gate to fall because if it falls, it will hit the bumper and it will get dented. Don't take them off both at the same time.
Just one little thing: When you're tightening it, you see the tailgate cable's made to go around the flint in this bolt. You need to lift up and make sure the tailgate cable goes on the bolt, and then tighten it. This allows that to keep moving. If you're tightening it up with getting it in that right spot, basically what will happen is your tailgate will just going to stay like this. This would end up pinching into there and probably damaging and scratching things. That's about it.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.
In this video we're going to be working with our 1996 GMC Sierra K-1500. We're going to show you how to remove and replace your tailgate latch rods which if stretched, rusted, or broken can cause the tailgate to be difficult to open or have it stuck in the open position.
If you like this video, please click subscribe. We have a ton more information on this truck, as well as many other makes and models. If you need these parts for your vehicle, you can follow the link down in the description over to 1AAuto.com.
Here are the items you'll need for this repair: flat blade screwdriver, Phillips screwdriver, 8-13mm sockets, ratchet, socket extension, T40 socket
If your tailgate is stuck closed, remove the bezel by popping it off with a trim tool or a flat blade screwdriver. Ours is missing. All you have to do is these latches usually get a little stretched out, these rods, you just have to pry them over until they release. Remove the six Phillips head screws around the perimeter of the tailgate cover with a Phillips head screwdriver. Now our tailgate liner has two 8mm screws in it. I believe that these are self-tappers that somebody put in here because you can see it's kind of wrinkled up. They probably just did that to help keep it down. If you have some in there, it's not uncommon, just remove them with the appropriate sized socket and ratchet. Ours are 8mm. Remove the two 13mm bolts in the top center of the tailgate cover, do this with a 13mm socket and ratchet, and remove the cover from your tailgate.
Remove the T40 Torx bolt with a T40 Torx socket, ratchet, and extension. You may want to hold the handle in place while you do this. Pop up the plastic clips on the latch rods. You may need a small flat blade screwdriver for this, but ours are moving fairly easily. Should just be able to do them by hand. Then pull the latch rod straight back out of the clip, same thing on the other side, and remove your handle from the tailgate.
Lift up on your tailgate slightly. Lift up on the little metal safety here so you can slide the cable forward into the larger opening and pop it out. Remove the T40 Torx for the cable. Remove the remaining two T40 Torx bolts. There is a small spacer or washer back here you want to make sure you don't loose when you take this off. See, right when you loosen it, it slides out. Remove the latch. You may have to reach over and just pop up the other end of the latch rod and remove it from the tailgate.
Here we have our old tailgate latch rod that we removed from our vehicle and our new part from 1AAuto.com. As you can see, these parts are nearly identical. There are some minor aesthetic differences with this little damper here. They do both have a rubberized end here, the same hook, length, and the same tab on this end. Now, these latch rods can become rusted, bent, broken or get stretched out and not allow your tailgate to release fully. A new pair of latch rods could be exactly what you need to get your tailgate functioning normally.
These are sold as a pair, however we're only showing you one here because both sides are identical. The kit even includes a new set of clips, which will pop into your old handle. You can see, it's not uncommon to break these when it comes out, so you can make sure that you can get through the whole job start to finish without needing any extra parts. If your tailgate is difficult to open or requires a lot of force, this new part from 1A Auto is going to go in direct fit, just like your original equipment and fix you up right.
Install your new latch rod into the latch. Carefully send it into the tailgate. You, again, may need to go over to the opening and just help get that hook over the end. Line up your two T40 Torx bolts. Don't forget to slide the plastic spacer back into place before tightening your bolts down with your T40 Torx socket, ratchet, and extension.
Install the T40 Torx bolt at the bottom of the cable. Make sure the hook at the top is facing the correct direction so the tab faces in toward the middle of the truck and will lock back over the stud. This bolt is shouldered, so it's going to bottom out before it's completely clamped, so this allows room to move around.
Lift up on your tailgate, slide the larger part of the cable over the tab, and then lock it into place. If your latch hold down is broken, simply take a small flat blade screwdriver, pop the old one out, pop your new one in. Now, we are installing a new handle so we didn't have to do that. The process for installing the old handle with the repaired tab and a new handle will be exactly the same.
Simply pop the top in. Slide the latch rods into their openings and engage the clips. Slide the handle back into place. Start reinstalling your hardware. Now the top two bolts on our handle went through the plastic tailgate cover. If yours don't, install them now. But since ours do, we'll install the top two bolts just a couple of threads to help keep everything aligned while we tighten down our T40 Torx bolt at the bottom. We'll take the bolts out, so now we know that everything is going to line up, and reinstall our plastic cover.
We'll reinstall our two 13mm bolts. Don't forget the washers if yours has them. We'll tighten down our two 13mm bolts with our 13mm socket and ratchet. We'll then reinstall the six Phillips head screws around the perimeter. We had our self-tapping screws that I'll reinstall as well. Open the handle. Slide the bezel up and around. Simply push all four corners to engage the clips. Close your tailgate and you're good to go.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
All right. So to do this job, you're gonna need one simple tool. A plastic trim tool. Something that I want to show you, if you look at the backside of the little bezel, you're gonna see these little ears. That's where we're gonna be looking for with our plastic trim tool. We're gonna come right down right where that is, and then we'll pop it off. So, I'm gonna come like this. Give it a little twist. There we are. Do the same on the bottom. Okay. There we are. Let's get this puppy installed. Just gonna line it up. It should wanna press right in. Couple loving bonks. Get those clips in there. Beautiful.
Tools used
So, now that we have the tailgate down, we have a clear view of all of our mounting bolts. We have two here, 13-millimeter. And then, if you were to go around, more than likely you have some Phillips heads. We're gonna remove them all. Here we go. Bring up the tailgate. Now, we can see what's going on in there. Let's see about popping this off of here. Here we are.
Now, this one right here has been broken for a while so it has a little wire tie. I'm just gonna get that right out of there using some cutters. Awesome. Now, you got these little white clips. They should kinda pry off of the bar there. And then, once you have it flipped up you can take the rod right off. This one obviously flips down. Here we are. Slide that out of right there. Here it is.
It's time to get this in here, just get it kinda lined up. You can grab your little rods. We're gonna put it through the hole just like that, and we're gonna spin this around so the lock comes around and clips right onto the rod. Give it a wiggle. That feels great. Do the same to the other one. Bright that one up and around. Lock it in. Perfect.
Get that started in there. We're just gonna turn it and try to make sure these bolt holes are lined up and they're not like that. Line them up nice. You see, when I tightened it, it kinda turned a little bit. Here we are. Let's get this back up on here. Line our bolt holes. Here we are. Now, I'm gonna go around the sides, start all those in as well. All right, let's start snugging them all up.
Let's get this puppy installed. I'm just gonna line it up. Make sure you wanna press right in. A couple of loving bonks. Put those clips in there. Beautiful.
