Caliper Hardware Kit Front - 1ABRX00021

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Front or Rear Location:   Front

Replace that caliper hardware today with this high quality replacement set!


  • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Direct replacements
  • Built to strict quality control standards

This caliper hardware kit makes a great replacement and has good cost savings over the factory parts.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:41)
    • Loosen the lug nut covers with a 22mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:11)
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
  3. step : Removing the Rotor and Brake Pads (1:23)
    • Remove T55 Torx bolts from the brake caliper with a T55 Torx bit and ratchet
    • Use either a C-clamp to squeeze the rotor or a screwdriver to pry the brake caliper off
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the two 18mm bolts from the caliper bracket
    • Slide the rotor off
  4. step : Preparing the Rotor and Brake Caliper (3:09)
    • Apply brake cleaner to either side of the rotor
    • Apply brake grease to either end of your brake pads
    • Use a wire brush to clean up the brake slides on the caliper bracket
  5. step : Replacing the Brake Caliper (3:46)
    • Push the rotor back into place
    • Twist on a lug nut
    • Put the caliper back into place and tighten the two 18mm bolts
    • Torque the 18mm bolts to 75 ft/lbs
    • Push the brake pads into place, using a hammer if necessary
    • Using an old brake pad, put it on to the caliper pistons and tighten it in with the C-Clamp
    • Grease up the caliper bolts
    • Put the caliper back into place
    • Slide the slide bolts back in
    • Torque the bolts to 30 ft/lbs
  6. step : Reattaching the Wheel (5:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the hubcap and tighten the caps
  7. step : Testing the Brakes (6:20)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Brake Fluid
  • Brake Parts Cleaner

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 22mm Socket

  • Torx Drivers & Sockets

  • T55 Torx Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007Cadillac Escalade Cadillac Escalade Front Caliper Hardware Kit
2007Chevy Avalanche Chevy Avalanche Front Caliper Hardware Kit
2005-2006Chevy Silverado 1500 Chevy Silverado 1500 Front Caliper Hardware Kit
2007Chevy Silverado 1500 Classic Chevy Silverado 1500 Classic Front Caliper Hardware Kit
2007Chevy Suburban 1500 Chevy Suburban 1500 Front Caliper Hardware Kit
2007Chevy Tahoe Chevy Tahoe Front Caliper Hardware Kit
2005-2006GMC Sierra 1500 GMC Sierra 1500 Front Caliper Hardware Kit
2007GMC Sierra 1500 Classic GMC Sierra 1500 Classic Front Caliper Hardware Kit
2007GMC Yukon GMC Yukon Front Caliper Hardware Kit
2007GMC Yukon XL 1500 GMC Yukon XL 1500 Front Caliper Hardware Kit
Only 1 left in stock
Part #: 1ABRX00021

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(06:50 min)