Replaces

Cadillac CTS STS Wheel Bearing & Hub Assembly - 1ASFK02064

Specifications:

  • Comes as a SET of 4
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT & REAR
  • 3 Bolt Triangular Flanges
  • Fits 5 Lug Wheels
  • Studs already installed
  • Built to strict quality control standards
  • Built in ABS sensor with correct plug configuration
  • Fit RWD (Rear Wheel Drive) Models only
    • Do NOT fit V-Series with 6 Stud Hub
    • Do NOT fit AWD (All Wheel Drive) Models
Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:30)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Rotor (2:20)
    • Remove the T30 Torx bolt from the rotors
    • Remove the two 18mm bolts holding the caliper bracket to the spindle
    • Secure the caliper with a bungee chord
    • Remove the rotor
  3. step : Removing the Hub (3:20)
    • Disconnect the ABS connector from the backing plate
    • Disconnect the ABS sensor wiring harness
    • Remove the three 18mm bolts from the spindle
    • Remove the 18mm bolt from the back of the spindle
    • Hammer out the hub
    • Remove the hub and the dust shield
    • Tap the back of the ABS sensor out of the spindle with a flat blade screwdriver and hammer
  4. step : Installing the Hub (5:45)
    • Clean the bore of the spindle with a wire brush
    • Line up the dust shield
    • Insert the hub into place
    • Line up the top bolt
    • Hand-tighten the other two bolts
    • Torque the wheel hub bolts to 100 foot-pounds
    • Reconnect the ABS harness container
    • Reconnect the ABS wiring harness
    • Apply a thin coat of brake grease to the hub
  5. step : Installing the Rotor (7:40)
    • Insert the rotor into place
    • Thread the T30 Torx bolt into place
    • Lower the brake caliper to the rotor
    • Start the two 18mm bolts to the brake caliper
    • Torque the bolts to 96 foot-pounds
  6. step : Reattaching the Wheel (8:40)
    • Slide the wheel into place
    • Start the 19mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 18mm Wrench

4.3 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
1
0
0
2007 Cadillac CTS Hubs
First, Very Fast Delivery and Packaged Well, Watched Video and was able to Install in about an Hour Each, Fit was like it should be and am Very Happy, Wheel Bearing Hum is Gone and I am Very Happy.

Thanks, Jim Hays
March 13, 2017
Purchased
1 year ago
Wheel bearings and hub
Best timing ever. The order came in unexpectedly. I’m satisfied with the quality of the parts.
April 26, 2018
Purchased
1 month ago
Video Incomplete
Your video showed the easier front hub replacement, did not show that a puller would be needed for the back.
October 17, 2017
Purchased
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Does this fit the Cadillac STS ���v8��� or the ���v6���?
Zach C on Apr 18, 2018
BEST ANSWER: This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. Please feel free to call our customer service department for clarification @ 888-844-3393.

Vehicle Fit

  • 2003-2007 Cadillac CTS Front & Rear for Models with 5 Lug Wheels Wheel Bearing & Hub Assembly 4 Piece Set
  • 2005-2011 Cadillac STS Front & Rear for Models with 5 Lug Wheels Wheel Bearing & Hub Assembly 4 Piece Set Rear Wheel Drive

This part replaces:

  • Hollander 538-01589
  • OE # 25693148
  • Hollander 538-01724
  • TRQ BHA53297
Part #: 1ASFK02064


How-to Video:

(10:32 min)