1ADSH01551-Cadillac CTS STS Rear Driveshaft Center Support Bearing

Replaces

Cadillac CTS STS Rear Driveshaft Center Support Bearing DIY Solutions

1ADSH01551

Part Details

This part replaces:

  • Dorman 934-610
  • OE # 88951975
  • Anchor NBHB3074A
  • Anchor 6104
  • DIY Solutions ADS00274
FREE SAME DAY SHIPPING
Save 53%
List: $138.95 Save: $74.00
Only 1 left in stock
Part 1ADSH01551
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

DIY Solutions
Brand #: ADS00274

Frequently bought together

Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Your DIY Solution—Complete Repair in One Purchase

Do you need an assortment of parts to complete a repair? Stop searching for parts individually and complete your repair in a single purchase with a customized kit or set from DIY Solutions.

High-Quality Parts From Trusted Brands

Parts in DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.

Guaranteed Fit

DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.

Highest Quality Materials

Made from highest quality materials that meet or exceed OEM standards

Direct Fit Replacement

Direct fit replacement part guaranteed to fit and function properly for your specific application

Quality Tested

Quality tested and built to a strict level of product standards

Item Condition: New

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Exhaust (0:47)
    • Raise and support the vehicle
    • Disconnect the O2 sensor wiring harnesses
    • Remove the O2 sensors from the exhaust with a 22mm wrench
    • Remove the four 14mm bolts from the exhaust
    • Allow the exhaust to hang
    • Loosen the two 13mm bolts from the exhaust cross brace
    • Remove one 13mm bolt from the exhaust cross brace
    • Pull the cross brace aside
    • Apply rust penetrant to the exhaust hangers
    • Pull off the exhaust hangers
    • Pull down the exhaust
  2. step : Removing the Driveshaft (3:10)
    • Mark the driveshaft and the flange with a marker in two places at each end
    • Remove the first two 18mm bolts that connect the driveshaft to the differential coupling
    • Put the transmission in neutral
    • Turn the driveshaft by hand
    • Remove the remaining 18mm bolt
    • Put the transmission in park
    • Remove the first two 18mm bolts that connect the driveshaft to the transmission coupling
    • Put the transmission in neutral
    • Turn the driveshaft by hand
    • Remove the remaining 18mm bolt
    • Put the transmission in park
    • Pry the driveshaft back with a pry bar
    • Remove the two 15mm bolts from the driveshaft support
    • Support the driveshaft with a jack
    • Pry the driveshaft off the transmission with a pry bar
    • Pry the driveshaft off the differential with a pry bar
    • Lower the jack
    • Remove the driveshaft
  3. step : Removing the Driveshaft Center Support Bearing (6:53)
    • Mark the spline alignments with a marker and/or score marks
    • Cut the bearing boot clamp with wire cutters
    • Peel back the boot
    • Pull the two driveshaft sections apart
    • Pull off the boot
    • Pull off the o-ring
    • Tap off the dust ring with a hammer and punch
    • Remove the snap ring with snap ring pliers
    • Attach a bearing separator behind the bearing
    • Apply rust penetrant to the bearing
    • Tighten the bearing separator nuts with a 19mm socket and a 3/4" Wrench
    • Install the bearing separator legs
    • Remove the nuts from the bearing separator legs
    • Install the top of the bearing separator
    • Fasten the nuts onto the top of the bearing separator
    • Crank the bearing separator with a 17mm socket and ratchet
    • Remove the bearing
    • Remove the bearing separator from the drive shaft
  4. step : Installing the Driveshaft Center Support Bearing (10:01)
    • Apply grease to the bearing journal
    • Slide the bearing onto the driveshaft
    • Tap the bearing on with a washer and a hammer
    • Remove the washer
    • Slide the snap ring on with snap ring pliers
    • Tap the snap ring into place with a hammer and punch
    • Clean the driveshaft splines
    • Apply lubricant to the driveshaft splines
    • Slide the dust shield onto the driveshaft
    • Tap the dust shield on with a hammer and pipe
    • Slide the rubber boot onto the driveshaft
    • Slide the o-ring onto the rub boot
    • Place the clamp on the rubber boot
    • Line up the driveshaft alignment marks
    • Slide the two driveshaft parts together
    • Check the driveshaft alignment
    • Adjust the driveshaft alignment if necessary
    • Tighten the clamp with the crimping tool
  5. step : Switching the Heat Shield Over (13:30)
    • Remove the two 10mm bolts holding the heatshield to the old bearing
    • Pull the heat shield off the bearing
    • Pull the spacers off the bearing
    • Push the spacers onto the new bearing
    • Place the heat shield on the new bearing
    • Insert the two 10mm bolts into the heat shield
  6. step : Installing the Driveshaft (14:15)
    • Lift the driveshaft into place
    • Line up the bolt holes with the differential
    • Line up the bolt holes with the transmission
    • Put the driveshaft support into place
    • Start the two 15mm bolts into the driveshaft support by hand
    • Line up the driveshaft marks with the transmission marks
    • Line up the differential marks with the driveshaft marks by turning the differential flange
    • Clean the driveshaft bolts with brake cleaner
    • Start the 18mm bolts into the differential coupling
    • Put the transmission in neutral
    • Apply thread locker to the bolts
    • Tighten the 18mm bolts to 63 foot-pounds of torque
    • Start the 18mm bolts into the transmission coupling
    • Apply thread locker to the bolts
    • Tighten the 18mm bolts to 63 foot-pounds of torque
    • Tighten the two 15mm bolts on the driveshaft support to 37 foot-pounds
  7. step : Installing the Exhaust (17:55)
    • Hook the muffler onto the rear two exhaust hangers
    • Lift the exhaust into place
    • Put the exhaust cross brace into place
    • Start the exhaust cross brace bolt by hand
    • Attach the remaining exhaust hanger
    • Tighten the two 13mm bolts into the exhaust cross brace
    • Replace the exhaust gaskets if necessary
    • Line up the exhaust bolt holes
    • Start the four 14mm bolts into the exhaust flanges
    • Tighten the 14mm bolts to 16 foot-pounds
    • Put the O2 sensors into place
    • Use an O2 sensor socket to tighten the O2 sensors to 40 foot-pounds
    • Connect the O2 sensor wiring harnesses

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Brake Parts Cleaner
  • Liquid Thread Locker
  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Crimper
  • Wire End Cutters
  • Snap Ring Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 18mm Socket
  • 17mm Socket
  • 15mm Socket
  • 13mm Socket
  • 10mm Socket

  • Specialty Tools

  • Bearing Puller

  • Wrenches - Metric

  • 19mm Wrench

  • Wrenches - SAE

  • 3/4 Inch Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Will this fit V models? V8 6.0 6 speed manual
Kevin T September 25, 2019
Thanks for your inquiry. This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit. The information we will need in order to assist you is your VIN.
Emma F September 25, 2019

Fits the following Makes:

Year Make Model Description
2003-2007Cadillac CTS Cadillac CTS Rear Driveshaft Center Support Bearing
2005-2010Cadillac STS Cadillac STS Rear Wheel Drive Rear Driveshaft Center Support Bearing

Part Interchange

Brand Label Part Number
DIY Solutions ADS00274

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
DIY Solutions
Brand #: ADS00274
Product Reviews
5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
My auto orders
The staff at 1A auto parts are trained professional who get it right the first time. Thank you for your friendly support team.
October 10, 2019
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


Cadillac CTS STS Rear Driveshaft Center Support Bearing DIY Solutions-1ADSH01551 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.