Replaces
Part Details
Product Features
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
In this video, we will be removing and installing a fog light bezel in a 2008 Cadillac CTS 4. If you need this part or other parts for your vehicle click the link in the description and head over to 1AAuto.com.
Take these pins out. You're going to untwist them. Then once they're untwisted you can pull them up just like that. Sometimes they don't untwist too well so you've got to like pry up underneath it. You can use your fingernail or like a straight head screwdriver.
I'm going to pull this panel up, put it aside, and then I can pull this weatherstrip towards the center of the vehicle to take it off. We'll do the same with this side. Pull up here. Pull up there. There is a fastener right there and a clip on the backside. We can take the weatherstrip towards the center, and this piece will come right off.
We're going to pull these little clips out with a trim tool. We sell these 1AAuto.com. Get in underneath there. There should be another one there, but it's missing on this vehicle. Right here. Right there.
I'm going to use a 10 millimeter socket and ratchet to take these 2, 10 millimeter bolts out. Okay, good.
I'm going to pull this push clip off. We're going to use clip trim tool, and then there's one right here we need to pull off. Pull that off. This is just a rubber shield that's attached to the bumper. We're going to leave it attached to the car on this side, and over here we'll do the same on the other side. This one's actually ripped right here, so we don't have to do that. And then this piece over here is already out, so we're all set on this side.
I'm gonna take these plastic push clips out with our trim tool. Pull it out, and we'll pull this one out. These other ones we can leave in. Those just hold this front skirt on. Pull that out. Pull this one out too.
So, we're going to disconnect the fog light. There's a little clip on the backside and then a clip on the front side. If you do them somewhat together you can pull it down. Pull the backside clip off first. You can pull on the front side. See? Two clips, just pull them out. I'm going to do the same for this side. Disconnect the fog light.
There's this air duct thing here. I'm going to pull that off. It looks like it's missing from the other side. This is there to force cool air onto the brakes while you're driving. This vehicle has headlight washers, so it sprays washer fluid on the headlights, so we're going to disconnect that. We're gonna use some needle nosed pliers and pry this clip off--just move it to the side a little bit to there.
We're going to take a right angle pick, get in there without stabbing yourself then go all the way around to loosen up the hose like that. We can twist it off. Just gonna work the hose back and forth and then it'll eventually come out. All right, when I pull this off, fluid is going to come out, so I just have this random bolt that's about the same size, so I'm gonna plug the hole with that, just like that. That'll keep the fluid in there, most of the fluid in there.
I'll use my clip tool. Pull these push clips off. I'm going to use our trim tool. Pull this one out. I'll have a little more play with this. It's a 10 millimeter bolt right there we're going to take out. Got that out. That process will be the same for the other side. Then you can pull this off.
Pull this out over here. Just with the grab, and pull it straightforward. All right, we're going to take this, say, seven millimeter bolt and pull this off with a seven millimeter socket, ratchet, and extension. You can take a screwdriver--just get it in here and push from behind here a little bit. There's some clips. They should pop off. I'm going to grab and pull a little bit so that's it at that point. There's these two white plastic clips. I'm gonna push down right here while pulling out slightly on the bezel. There's a clip right here as well. You can squeeze them and almost push them, and you can pop the bezel out.
For reinstall, we're going to align those two plastic clips and push those in, and push the front and it's in. Now we'll take our seven millimeter bolt and screw it in. The process will be the same for the passenger side.
We're gonna reinstall the bumper. Make sure that lines up over there. Line this up over here. Line that side up right there. You can take these 2, 10 millimeter bolts, put these in. We can snug these down.
We're gonna install this 10 millimeter bolt on the passenger side. When we're doing this you're going to want to make sure the body lines up with the bumper and then snug that down. Procedure will be the same for the driver's side. Connect the fog light connector, line it up then push so it locks in place. Same on the passenger side.
Right. Next we're gonna reconnect our headlight washer hoses. Most of our fluid leaked out, but if did this in a timely manner you would have fluid coming out of there. Then we're gonna move this clamp with some needle nosed pliers back to its original location right there. It goes just like that.
We're gonna reinstall this shield. Push that push pin through up top. Push this one in down here, just like so. Same for the driver's side.
Next we're going to install this brake cooling snorkel on the passenger side. Our driver's side is missing, so put a push pin right there, right there, and right here. A little push pin there--one right here, and then one right here.
All right, you're gonna install this liner. You're going to go up under here, and then to put the snorkel on it's going to click through like that. I'm going to put our push clips through there. Install these push clips right here, right here, and one right there. We're gonna put our push clips in up top here.
Now we're gonna reinstall this shield. We're gonna push this weatherstripping on sorta like that, and same with the other side just like that.
Now we're going to use these clips, reinstall these retainers. We're gonna reinstall this cover right here. Get that lined up. There's a little tab right there that lines up with. Lock that down. We're gonna reinstall this right here. Make sure you go under the weather strip over here and then press down.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
In this video we will be removing and reinstalling a fog light assembly in a 2008 Cadillac CTS4. If you need this part or other parts for your vehicle, click the link in the description and head over to 1aauto.com.
Take these pins out, you're gonna untwist them and then once they're untwisted you can pull them up. Just like that. Sometimes they don't untwist too well so you've got to like pry up underneath it. You can use your fingernail or like a straight head screwdriver. You're gonna pull this panel up, put it aside, then I can pull this weather strip towards the center of the vehicle to take it off. We'll do the same with this side. Pull up here and pull up there.
There's a fastener right there and a clip on the back side. I can take the weather strip towards the center and this piece will come right off. I'm gonna pull these little clips out with a trim tool. We sell these at 1aauto.com. Get in underneath there and there. There should be another one there but it's missing on this vehicle. Right here. Right there. I'm gonna use a ten millimeter socket and ratchet, just take these two ten millimeter bolts out. Alright, good.
We're gonna pull this push clip off, we're gonna use a clip trim tool and then there's one right here we need to pull off. Pull that off. This is just a rubber shield that's attached to the bumper. We're gonna leave it attached to the car on this side. And then over here, we'll do the same on the other side. This one's actually ripped right here, so we don't have to do that. And then this piece over here is already out, so we're all set on this side. We're gonna take these plastic push clips out, use our trim tool again. Pull it out and we'll pull this one out. These other ones, we can leave in. Those just hold this front skirt on. Pull that out. Pull this one out too.
So we're gonna disconnect the fog light. There's a little clip on the back side and then a clip on the front side. If you do them somewhat together, you can pull it down. Pull the backside clip off first, then you can pull on the front side. See. Two clips, just pull them out. I'm gonna do the same for this side. Disconnect the fog light. There's this air duct thing here, we're gonna pull that off. Looks like it's missing from the other side. This is there to force cool air onto the brakes while you're driving.
This vehicle has headlight washers. So it sprays washer fluid on the headlights. So we're gonna disconnect that. We're gonna use some needle nose pliers and then pry this clip off. Just move it to the side a little bit. Right there. We're gonna take a right angle pick and get in there without stabbing yourself. And you go all the way around to loosen up the hose. Like that. And we can twist it off. Just gonna work the hose back and forth and then it'll eventually come out.
Alright when I pull this off, fluid's gonna come out so I just have this random bolt that's about the same size. So I'm gonna plug the hole with that. Just like that and that'll keep the fluid in there. Most of the fluid in there.
I'm gonna use my clip tool, whoops, pull these push clips off. Alright, use our trim tool. Try to pull this one out, I'll have a little more play with this. There's a ten millimeter bolt right there we're gonna take out. Take that out. And that process would be the same for the other side, and then you can pull this off. Pull this out over here. Just grab and pull it straight forward. Pull the fog light assembly out, we're gonna take this seven millimeter screw out with a seven millimeter socket, extension and a ratchet. Get that out. You can grab it. There's these little locks and here, you can grab a little screwdriver, straight screwdriver, push in on the locks while pulling on the fog light. Pull it right out.
To reinstall, we're gonna take the fog light, line it up with the locks, click it in, make sure those locks are lined up and take our seven millimeter screw and tighten it down. Remember it is in plastic so not too tight. Just snug. The process will be the same for the passenger side. We're gonna reinstall the bumper, make sure that lines up over there. Line this up right here. Line that side up, and that. We can take these two ten millimeter bolts, put these in. We can snug these down. We're gonna install this ten millimeter bolt on the passenger side. When we're doing this, you're gonna wanna make sure the body lines up with the bumper, and then snug that down. Procedure will be the same for the driver's side. Connect the fog light connector, line it up and then push so it locks in place. Same on the passenger's side.
Alright next we're gonna reconnect our headlight washer hoses. Most of our fluid leaked out but if you did this, in a timely manner, you would have fluid coming out of there. Then we're gonna move this clamp with some needle nose pliers, back to it's original location. Right there. And that goes just like that. We're gonna reinstall this shield, push the pushpin through up top, push this one in down here. Like so. Same for the driver's side.
Next we're gonna install this brake cooling snorkel on the passenger side. Our driver's side is missing, so. Put a pushpin right there, right there, right here. Pushpin there, one right here and then one right here. Alright we're gonna reinstall this liner. You're gonna go up under here and then to put the snorkel on, just gonna click through like that. I'm gonna put our push clips through there. Install these push clips right here and here and one right there. We're gonna put our push clips in up top here. Whoops.
Now we're gonna reinstall this shield, we're gonna push this weather stripping on. Just like that. And same with the other side. Just like that.
Now we're gonna use these clips, reinstall these retainers. And then reinstall this cover right here, get that lined up. There is a little tab right there that lines up with, lock that down. And reinstall this right here. Make sure you go under the weather strip over here. And then press down.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
