Replaces

Cadillac CTS Chevy Camaro Brake Kit Rear - 1ABFS01309

This rear brake rotor & pad set is just what you need to get your vehicle stopping in good order again!

Brake Pad Specifications:

  • Professional Grade Ceramic Enhanced Disc Brake Pads
  • 4 Piece REAR brake pad set
  • Includes shims
  • Direct replacement

Brake Rotor Specifications:

  • Come as a PAIR
  • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • Replaces dealer part numbers: 13501315, 15267107, 20808621
  • Fits 5 lug wheels
  • Vented
  • 12.40" (315mm) diameter

This brake rotor & pad set makes great replacements and has excellent value over the price of dealer brakes.

Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

100% CNC-Machined to Exact OE Specs

100% CNC-Machined to exact OE specs and balanced to reduce vibration

Cast from OE Grade Alloy

Manufactured from OE Grade G3000 Casting Alloy

Non-Directional Surface Finish

Non-Directional Rotor Surface Finish helps ensure smoother, quieter, and more effective braking

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:54)
    • Loosen the five 22mm lug nuts with a breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts
    • Slide the wheel off the hub
  2. step : Removing the Brakes (1:26)
    • Place a wrench on one wheel stud to counterhold the brake rotor
    • Remove the T30 Torx screw from the brake rotor
    • Remove the two 14mm guide bolts from the caliper
    • Pull the caliper off its bracket
    • Hang the caliper aside with a bungee cord
    • Pry the brake pads from the caliper bracket with a flat blade screwdriver
    • Remove the two 16mm bolts from the caliper bracket
    • Make sure the emergency brake is off
    • Hit the rotor hub with a hammer to loosen it
    • Pull off the brake rotor
  3. step : Preparing the Brakes (3:35)
    • Pry the brake shims out of the caliper bracket with a flat blade screwdriver
    • Clean the brake shims with a wire brush
    • Clean the caliper bracket with a wire brush
    • Apply brake grease to the caliper bracket
    • Slide the caliper pins out of the caliper bracket
    • Clean the old grease off the caliper pins
    • Apply brake grease to the caliper pins
    • Slide the pins into the caliper bracket
    • Snap the shims onto the caliper bracket
    • Apply grease to the shims
    • Clean the hub surface with a wire brush
    • Apply brake grease to the hub surface
  4. step : Installing the Brakes (7:06)
    • Slide the rotor onto the hub backwards
    • Spray the back of the rotor with brake cleaner
    • Slide the rotor off the hub
    • Slide the rotor onto the hub normally
    • Spray the front of the rotor with brake cleaner
    • Install the T30 screw into the rotor
    • Put the caliper bracket into place
    • Start the two 16mm bolts into the caliper bracket
    • Tighten the two 16mm bolts to 30 foot-pounds of torque
    • Tighten the 16mm bolts an additional 90 degrees
    • Install the brake pads into the caliper bracket
    • Apply brake grease to the back of each brake pad
    • Remove the bungee cord from the caliper
    • Compress the caliper piston with pliers
    • Slide the caliper onto the bracket
    • Install the two 14mm bolts into the caliper
    • Tighten the two 14mm bolts to 20 foot-pounds
  5. step : Installing the Wheel (10:16)
    • Slide the wheel onto the hub
    • Start the five 22mm lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 140 foot-pounds in a star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Brake Parts Cleaner

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 16mm Socket
  • 14mm Socket
  • 22mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Bit

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2008-2014 Cadillac CTS Rear Brake Kit for Models with RPO Code JE5 (4 Wheel ABS Brakes) Ceramic
  • 2010-2014 Chevy Camaro Rear Brake Kit V6 3.6L Ceramic
Only 2 left in stock
Part #: 1ABFS01309



How-to Video:

(10:49 min)