Replaces

Brake Rotor Rear Pair Nakamoto 55073-DSZ - 1APBR00044

Part Details

  • Brake Rotor Type: Cross Drilled & Slotted
  • Quantity: Pair
  • Brake Rotor Coating: Zinc Coated
  • Front or Rear Location: Rear
  • Rear Brake Rotor Specifications:
    Vented
    12.80" (325mm)
    6 Lug
  • Product Line: Performance

These rear performance brake rotors are just what you need to get your vehicle stopping great again!

Specifications:

  • Comes as a matched pair
    • Includes both LH (Driver) & RH (Passenger) Side REAR
  • Cross drilled, Slotted, And Zinc Coated
  • Replaces dealer part numbers: 15134671, 15158975, 177882, 8151589750, 81515 89750, 15134671
  • Vented
  • Fits 6 lug wheels
  • 12.8" (325 mm) Diameter

Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove wheel. (1:15)
    • Remove hub cap or center cap if you have it.
    • While your car is still on the ground, use your 19mm socket to loosen your lug nuts.
    • Jack up and secure your car with jack stands.
    • Remove the lug nuts with your 19mm socket and ratchet.
    • Remove the wheel and set aside.
  2. step : Remove the rear brake calipers (1:46)
    • Use a screwdriver to force the pistons back in.
    • Remove the two 14mm bolts to remove the calipers.
    • Use a wire tie to fasten the caliper out of the way.
    • Use your screwdriver to pry out your brake pads.
    • Remove the two 18mm bolts on the caliper bracket to remove it.
    • Remove the caliper bolt sleeves.
    • Check their condition and clean them with a wire brush if necessary.
    • Pull off the brake rotor.
    • Screw in the two 10M bolts to remove the rotor.
    • Take care not to damage the lug studs.
  3. step : Install new rear brake rotor and pads (6:30)
    • Clean new rotor with brake cleaner.
    • Insert your new pads into the brackets.
    • Put your caliper bracket back on, and tighten the bolts to 90-100 ft lbs.
    • Compress the caliper piston with a c-clamp to reset the pistons.
    • Mount the caliper on the bracket and torque the bolts in to 15-20 ft lbs.
  4. step : Put the rear wheel back on (10:25)
    • Make sure to use a star pattern when putting your wheel lugs back on.
    • Tighten to 100 ft lbs.
    • Replace hubcap/center cap.
  5. step : Test and set brakes (11:00)
    • Before driving the car again, start it up and pump the brakes a few times to get the pistons in the brakes in place.
    • Test the brakes in your driveway before taking the car onto the road.
    • Set your rotors by evenly braking from 30mph to 10mph, 50mph-30mph and finally 70mph to 40mph.
    • This is best done on a straight back road without any traffic.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Large Hammer
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • M10 x 7cm bolts
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2004-2007Buick Rainier Buick Rainier Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2003-2006Chevy SSR Chevy SSR Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2002-2007Chevy Trailblazer Chevy Trailblazer Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2002-2006Chevy Trailblazer EXT Chevy Trailblazer EXT Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2002-2007GMC Envoy GMC Envoy Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2002-2006GMC Envoy XL GMC Envoy XL Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2004-2005GMC Envoy XUV GMC Envoy XUV Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2003-2007Isuzu Ascender Isuzu Ascender Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2002-2004Oldsmobile Bravada Olds Bravada Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2005-2006Saab 9-7X Saab 9-7X Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto

This part replaces:

  • Nakamoto 55073-DSZ
Part #: 1APBR00044


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: 55073-DSZ

How-to Video:

(11:30 min)