Replaces

Brake Rotor Rear Pair Nakamoto 54111-DSZ - 1APBR00045

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Brake Rotor Type:   Cross Drilled & Slotted
  • Quantity:   Pair
  • Brake Rotor Coating:   Zinc Coated
  • Front or Rear Location:   Rear
  • Rear Brake Rotor Specifications:
      13.70" (348mm)
      6 Lug
      Vented
  • Product Line:   Performance

These rear performance brake rotors are just what you need to get your vehicle stopping great again!

Specifications:

  • Comes as a matched pair
    • Includes both LH (Driver) & RH (Passenger) Side REAR
  • Cross drilled, Slotted, And Zinc Coated
  • Replaces dealer part numbers: 4L3Z-2C026-AB, 4U2Z-1V125-DA, 5L3Z-2C026-AA, 9L3Z-2C026-A, BL3Z-2C026-A, 4L3Z2C026AB, 4U2Z1V125DA, 5L3Z2C026AA, 9L3Z2C026A, BL3Z2C026A
  • Fits 6 Lug Wheel
  • Direct replacement
Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:41)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:08)
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
  3. step : Removing the Brake Pads and Rotor (1:33)
    • Remove the two 10mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pull the rotor off
    • Pry the brake pads off the caliper with a flat blade screwdriver
    • Clean the friction areas with a wire brush
    • Clean the slides with a wire brush
    • Pry off the brake pad slides with a flat blade screwdriver
    • Tap the slides on with a hammer
    • Apply white grease to the slides
  4. step : Installing the Brake Pads and Rotors (5:02)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Slide the rotor on
    • Adjust the emergency brake, if necessary, by turning the star wheel with a flat blade screwdriver
    • Install the new brake pads into the caliper
    • Put the caliper on
    • Thread the two 10mm bolts by hand
    • Tighten the 10mm bolts to 17 foot-pounds
  5. step : Reattaching the Wheel (7:11)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  6. step : Testing the Brakes (7:35)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Wire Brush
  • Large C-Clamp
  • Chisel
  • Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 10mm Socket

5.00/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
2
0
0
0
0
Brakes
The purchase I just made on the brakes are very good Im very happy with the customer service for your company they treat me very well the free shipping is just incredible and the product is outstanding I bought a quite a few things to your company and will continue to buy and have recommended 1A Auto 2 who ever needs parts thank you very much
July 1, 2017
Great prices and great value
Like the parts the way they fit ,1-Auto sell great value and great prices will buy my parts from 1-auto
April 30, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004Ford F150 Truck Ford F150 Truck New Body Style Rear for Models with 6 Lug Wheels Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2005-2011Ford F150 Truck Ford F150 Truck Rear for Models with 6 Lug Wheels Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
2006-2008Lincoln Mark LT Lincoln Mark LT Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
Part #: 1APBR00045


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: 54111-DSZ

How-to Video:

(08:07 min)