These performance brake rotors are just what you need to get your vehicle stopping great again!

Specifications:

  • Comes as a matched pair
    • Includes both LH (Driver) & RH (Passenger) Side Front
  • Cross drilled, Slotted, And Zinc Coated
  • Replaces dealer part numbers: F67Z 1125 BA, F67Z1125BA, F67A 1125 BA, F67A1125BA, F67A BA, F67ABA
  • Fits 5 Stud Wheels
  • Fits 4WD models only
  • Outside Diameter: 11.25 Inches

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:07)
    • Pry off the lug nut cover
    • Loosen the lug nuts.
    • Raise and secure the vehicle.
    • Remove the lug nuts and the tire.
  2. step : Remove the calipers (1:42)
    • Use your 1/2" socket and ratchet to remove the caliper bolts
    • Use a flat blade screwdriver or pry bar to compress the caliper pistons
    • Pry the caliper of the rotor.
    • Remove the two 15 mm caliper bracket bolts.
  3. step : Replace the rotor (4:21)
    • Pry off the grease cap.
    • Use your pliers to remove the cotter pin.
    • Remove the 27 mm nut.
    • Pull the rotor off.
    • Insert the outside bearing race.
    • Use your race installation tools to tap the race into place.
    • Install the interior race.
    • Apply bearing grease to the races.
    • Pack the interior bearing with bearing grease.
    • Use a paper towel to keep your race tools tidy and install the interior bearing.
    • Apply grease to the exterior race.
    • Clean the spindle and mount the rotor.
    • Install the exterior bearing and apply bearing grease.
    • Put the nut and washer on, and tighten it with your socket and ratchet to seat the bearing.
    • Spin the rotor and loosen the nut and then tighten it again.
    • Do this till the bearing is seated, then put the cotter pin through.
    • Replace the dust cap.
  4. step : Install the calipers (15:20)
    • Mount the caliper bracket and secure it with your 15 mm socket and ratchet
    • Torque these bolts to 80 ft lbs.
    • Compress the caliper with a C-Clamp
    • Apply anti-seize grease to the edges of the brake pads and insert them into the brackets.
    • Mount the calipers to the brackets and torque the bolts to 15 ft lbs.
  5. step : Put the wheel on (18:05)
    • Thread the lug nuts on.
    • Wiggle the wheel to make sure there isn't any play in the bearings.
    • Lower the vehicle
    • Torque the lug nuts to 100 ft lbs.

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 27mm socket
  • 15mm Socket
  • 19mm Socket

  • Sockets - SAE

  • 1/2 Inch Socket

  • Specialty Tools

  • Race Installation Tools

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-2000 Ford Explorer 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2001 Ford Explorer 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair 4 Door Performance Nakamoto
  • 1998-2000 Ford Ranger 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2001-2003 Ford Ranger 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 4 Wheel ABS Brakes Performance Nakamoto
  • 2001-2002 Mazda B2300 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2003 Mazda B2300 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 11.25" (286mm) Diameter Rotors Performance Nakamoto
  • 1999-2001 Mazda B2500 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 1998-2002 Mazda B3000 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2003 Mazda B3000 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 11.25" (286mm) Diameter Rotors Performance Nakamoto
  • 2003 Mazda B4000 Truck 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 11.25" (286mm) Diameter Rotors Performance Nakamoto
  • 1997-2001 Mercury Mountaineer 4 Wheel Drive Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto

This part replaces:

  • Nakamoto 54035-DSZ
Part #: 1APBR00073



Nakamoto
Brand #: 54035-DSZ

How-to Video:

(19:32 min)