Specifications:

  • Comes as a matched Pair
    • Includes both LH (Driver) & RH (Passenger) Side Rear
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 5 Stud Wheels
  • Solid - not vented
  • 13.14" (334mm) diameter
Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:30)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:17)
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside and hang it with a bungee cord
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the brake pad slides
  3. step : Removing the Brake Rotor (2:42)
    • Remove the 17mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Clean the dirt and debris from the caliper bracket with a wire brush
    • Remove the Phillips screws from the rotor
    • Tighten M8 x 1.25 bolts into the rotor to remove it
    • Pull the rotor off
    • Pry out the rubber plug if needed and adjust the parking brake adjustor with a flat blade screwdriver
  4. step : Installing the New Brake Rotor (7:35)
    • Slide the rotor on and line it up with the appropriate holes in place
    • Adjust the parking brake adjuster if needed
    • Tighten the Phillips screws into the rotor
    • Press on the rubber cap
    • Clean both sides of the rotor with brake parts cleaner
    • Clean the brake pad slides with a wire brush
    • Apply grease to the caliper slides
    • Put the bracket back into place
    • Tighten the 17mm bolts
  5. step : Installing the New Brake Pads (12:15)
    • Apply grease to the brake pad tabs
    • Push the slides on with a flat blade screwdriver
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Tighten the 12mm bolts
  6. step : Reattaching the Wheel (15:14)
    • Slide the wheel into place
    • Start the 22mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 94 foot-pounds in a crossing or star pattern
  7. step : Testing the Brakes (14:07)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Bungee Cord
  • Anti-Seize Grease
  • Cloth Rags

  • Ratchets & Related

  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 17mm Socket
  • 22mm Socket

  • Wrenches - Metric

  • 17mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2007-2013 Acura MDX Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2010-2013 Acura ZDX Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2011-2016 Honda Odyssey Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
  • 2009-2015 Honda Pilot Rear Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto

This part replaces:

  • Nakamoto 31469-DSZ
Part #: 1APBR00122


Nakamoto
Brand #: 31469-DSZ

How-to Video:

(16:31 min)