Replaces

Brake Rotor Front Pair Nakamoto 55148-DSZ - 1APBR00327

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Front Brake Rotor Specifications:
      Vented
      5 Lug
      11.65" (296mm)
  • Brake Rotor Type:   Cross Drilled & Slotted
  • Quantity:   Pair
  • Brake Rotor Coating:   Zinc Coated
  • Front or Rear Location:   Front
  • Product Line:   Performance

Specifications:

  • Comes as a matched Pair
    • Includes LH (Driver Side) & RH (Passenger Side) Front
  • Cross drilled, Slotted, And Zinc Coated
  • Direct replacement
  • Fits 5 Stud Wheels
  • Vented
  • 11.65" (296mm) diameter
Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:58)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:57)
    • Remove the T30 Torx bit from the rotor
    • Remove 14mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. step : Removing the Brake Rotor (3:04)
    • Remove 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
    • If the rotor will not come off, thread the lug nuts and strike the hub area of the rotor with the ball end of a ball peen hammer
  4. step : Cleaning the Brake Parts (5:34)
    • Clean off any rust on the hub/centerbore with a wire brush
    • Coat the hub with brake grease
    • Install the rotor backwards and clean it with brake parts cleaner
    • Install the rotor and spray the front with brake parts cleaner
    • Reinstall the T30 Torx screw to the rotor
    • Remove the brake shims
    • Clean the shims with a wire brush
    • Remove the brake pad slides
    • Apply anti-seize fluid or white grease to the slides
    • Push the slides on with a flat blade screwdriver
  5. step : Installing the Caliper Bracket (8:30)
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 137 foot-pounds of torque
  6. step : Installing the New Brake Pads (8:57)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Install the new brake pads into the bracket
    • Apply brake grease to the pads
    • Put the caliper on
    • Thread bolts by hand
    • Tighten 14mm bolts to 20 foot-pounds
    • Clean the rotor with brake parts cleaner or mineral spirits
  7. step : Reattaching the Wheel (10:41)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Channel-Lock Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket
  • 14mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Bit

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2007-2009Chevy Equinox Chevy Equinox Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto
2007-2009Pontiac Torrent Pontiac Torrent Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto
2008-2010Saturn Vue Saturn Vue Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto
2007-2009Suzuki XL-7 Suzuki XL-7 Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto
Part #: 1APBR00327


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: 55148-DSZ

How-to Video:

(11:34 min)