Replaces

Brake Rotor Backing Plate Rear Dorman 924-213 - 1ABMX00082

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Design:   2 Piece Design
  • Front or Rear Location:   Rear

Specifications:

  • Fits the LH (Driver Side) or RH (Passenger Side) REAR
  • Comes in 2 pieces for easy installation without having to remove the axle shaft
  • Bolts to rear end
  • Made from stamped steel like originals, but coated with rust proof paint
  • Replaces dealer part numbers: 12476287, 19178785, 12472851, 19178786
  • Built to strict quality control standards
  • Will need to reuse original mounting hardware
  • Saves time over installing a standard backing plate!
  • Only fits vehicles that have rear disc brakes
    • Will NOT fit vehicles with rear drum brakes or with 4 wheel steering

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:42)
    • Loosen the lug nut covers with a 22mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:07)
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
  3. step : Removing the Brake Pads (1:22)
    • Remove the two 12mm bolts from the brake caliper
    • Attach a large C-clamp to the brake pads
    • Turn the C-clamp to push in the brake caliper pistons
    • Alternatively pry the pads into the caliper with a flat blade screwdriver
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  4. step : Removing the Brake Rotor (2:11)
    • Remove the two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  5. step : Disconnecting the Emergency Brake (2:44)
    • Remove the 8mm bolt from the emergency brake bracket
    • Pull off the emergency brake bracket
    • Pull off the emergency brake shoe
    • Pull the emergency brake cable out of its bracket
    • Pull the emergency brake cable off its clip
  6. step : Removing the Backing Plate (3:17)
    • Remove the four 18mm bolts from the backing plate
    • Strike the back of the backing plate with a hammer
    • Pull the emergency brake assembly forward
    • Break the backing plate apart with a hammer and screwdriver or wire cutters
  7. step : Installing the New Backing Plate (4:59)
    • Push the lower part of the backing plate onto the emergency brake assembly
    • Push the upper part of the backing plate onto the emergency brake assembly
    • Connect the two parts of the backing plate with their tabs
    • Slide the backing plate back
    • Push the rubber pad into place between the backing plate and the emergency brake
    • Insert the four 18mm bolts into the backing plate
  8. step : Reconnecting the Emergency Brake (6:38)
    • Pull the cap out of the emergency brake adjuster
    • Push the emergency brake rod in through the backing plate
    • Push the cap back into the emergency brake adjuster
    • Clip the emergency brake cable into the rod
    • Grip the emergency brake spring with vise-grip pliers
    • Pull the spring up
    • Have an assistant pull the emergency brake cable into the bracket
    • Put the emergency brake bracket into place
    • Insert the 8mm bolt into the bracket
    • Push the emergency brake shoe into place
    • Line up one brake shoe tab onto the adjuster
    • Pry the other tab onto the adjuster with a flat blade screwdriver
    • Turn the adjuster wheel with a flat blade screwdriver
    • The adjuster should be set so that the brake rotor slides on with some resistance
  9. step : Installing the New Brake Rotor (8:41)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 85 foot-pounds of torque
    • Remove the placeholder lug nut
  10. step : Installing the New Brake Pads (9:34)
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 12mm bolts by hand
    • Tighten bolts to 30 foot-pounds
  11. step : Reattaching the Wheel (10:06)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 22mm socket
  12. step : Testing the Brakes (10:45)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers
  • Wire Cutters

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 18mm Socket
  • 22mm Socket
  • 8mm Socket

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Two piece backing plates are the way to go.
These 2 piece backing plates worked out great for me. Easy to install and saves time and cost.
October 5, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does this part fit 03 s-10 ?
Bill C November 12, 2015
These will not fit the 2003 Chevy S10-Pickup. Below is a link for your parts, it also has been emailed to you! Thank you and have a great day! http://www.1aauto.com/brake-backing-plate-pair-rear/i/1abmx00064?f=363568&y=2003
Derek C November 17, 2015
Year Make Model Description
2000Cadillac Escalade Cadillac Escalade Brake Rotor Backing Plate Rear for Models with Rear Disc Brakes 2 Piece Design Dorman 924-213
2002-2006Cadillac Escalade Cadillac Escalade Brake Rotor Backing Plate Rear for Models with Rear Disc Brakes 2 Piece Design Dorman 924-213
2003-2006Cadillac Escalade ESV Cadillac Escalade ESV Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2002-2006Cadillac Escalade EXT Cadillac Escalade EXT Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2003-2005Chevy Astro Chevy Astro Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2002-2006Chevy Avalanche 1500 Chevy Avalanche 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2003-2014Chevy Express 1500 Van Chevy Express 1500 Van Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
1999-2000Chevy Silverado 1500 Chevy Silverado 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2001-2006Chevy Silverado 1500 Chevy Silverado 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes without Quadrasteer Dorman 924-213
2007Chevy Silverado 1500 Classic Chevy Silverado 1500 Classic Brake Rotor Backing Plate Rear Rear Disc Brakes without Quadrasteer 2 Piece Design Dorman 924-213
2000-2006Chevy Suburban 1500 Chevy Suburban 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2000-2007Chevy Tahoe Chevy Tahoe Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2003-2005GMC Safari GMC Safari Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2003-2014GMC Savana 1500 Van GMC Savana 1500 Van Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
1999-2000GMC Sierra 1500 GMC Sierra 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2001-2006GMC Sierra 1500 GMC Sierra 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes without Quadrasteer Dorman 924-213
2007GMC Sierra 1500 Classic GMC Sierra 1500 Classic Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes without Quadrasteer Dorman 924-213
2000-2007GMC Yukon GMC Yukon Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2000-2007GMC Yukon XL 1500 GMC Yukon XL 1500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
2000-2007GMC Yukon XL 2500 GMC Yukon XL 2500 Brake Rotor Backing Plate Rear 2 Piece Design for Models with Rear Disc Brakes Dorman 924-213
Part #: 1ABMX00082


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Dorman
Brand #: 924-213

How-to Video:

(11:15 min)