This Rear brake pad set is just what you need to get your vehicle stopping in good order again!

Specifications:

  • Profesional grade Ceramic Enhanced brake pads
  • 4 Piece REAR brake pad set
  • Includes shims
  • Direct replacements

This brake pad set makes a great replacement and has an excellent value over the price of dealer brake pads.

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quite braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:30)
    • Loosen the 22mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:17)
    • Remove the 12mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside and hang it with a bungee cord
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the brake pad slides
  3. step : Removing the Brake Rotor (2:42)
    • Remove the 17mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Clean the dirt and debris from the caliper bracket with a wire brush
    • Remove the Phillips screws from the rotor
    • Tighten M8 x 1.25 bolts into the rotor to remove it
    • Pull the rotor off
    • Pry out the rubber plug if needed and adjust the parking brake adjustor with a flat blade screwdriver
  4. step : Installing the New Brake Rotor (7:35)
    • Slide the rotor on and line it up with the appropriate holes in place
    • Adjust the parking brake adjuster if needed
    • Tighten the Phillips screws into the rotor
    • Press on the rubber cap
    • Clean both sides of the rotor with brake parts cleaner
    • Clean the brake pad slides with a wire brush
    • Apply grease to the caliper slides
    • Put the bracket back into place
    • Tighten the 17mm bolts
  5. step : Installing the New Brake Pads (12:15)
    • Apply grease to the brake pad tabs
    • Push the slides on with a flat blade screwdriver
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Tighten the 12mm bolts
  6. step : Reattaching the Wheel (15:14)
    • Slide the wheel into place
    • Start the 22mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 94 foot-pounds in a crossing or star pattern
  7. step : Testing the Brakes (14:07)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Bungee Cord
  • Anti-Seize Grease
  • Cloth Rags

  • Ratchets & Related

  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 17mm Socket
  • 22mm Socket

  • Wrenches - Metric

  • 17mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2007-2013 Acura MDX Rear Premium Posi Ceramic Brake Pads Nakamoto
  • 2010-2013 Acura ZDX Rear Premium Posi Ceramic Brake Pads Nakamoto
  • 2011-2016 Honda Odyssey Rear Premium Posi Ceramic Brake Pads Nakamoto
  • 2009-2011 Honda Pilot Rear Premium Posi Ceramic Brake Pads Nakamoto

This part replaces:

  • Nakamoto CD1281
Part #: 1ABPS00419

Ships Same Day for orders placed by 4 P.M. ET

Nakamoto
Brand #: CD1281

How-to Video:

(16:31 min)