Specifications:

  • Premium Posi Semi-Metallic Disc Brake Pads
  • 8 Piece Front & Rear Brake Pad Set
  • Direct replacement

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove wheel. (1:15)
    • Remove hub cap or center cap if you have it.
    • While your car is still on the ground, use your 19mm socket to loosen your lug nuts.
    • Jack up and secure your car with jack stands.
    • Remove the lug nuts with your 19mm socket and ratchet.
    • Remove the wheel and set aside.
  2. step : Remove the rear brake calipers (1:46)
    • Use a screwdriver to force the pistons back in.
    • Remove the two 14mm bolts to remove the calipers.
    • Use a wire tie to fasten the caliper out of the way.
    • Use your screwdriver to pry out your brake pads.
    • Remove the two 18mm bolts on the caliper bracket to remove it.
    • Remove the caliper bolt sleeves.
    • Check their condition and clean them with a wire brush if necessary.
    • Pull off the brake rotor.
    • Screw in the two 10M bolts to remove the rotor.
    • Take care not to damage the lug studs.
  3. step : Install new rear brake rotor and pads (6:30)
    • Clean new rotor with brake cleaner.
    • Insert your new pads into the brackets.
    • Put your caliper bracket back on, and tighten the bolts to 90-100 ft lbs.
    • Compress the caliper piston with a c-clamp to reset the pistons.
    • Mount the caliper on the bracket and torque the bolts in to 15-20 ft lbs.
  4. step : Put the rear wheel back on (10:25)
    • Make sure to use a star pattern when putting your wheel lugs back on.
    • Tighten to 100 ft lbs.
    • Replace hubcap/center cap.
  5. step : Test and set brakes (11:00)
    • Before driving the car again, start it up and pump the brakes a few times to get the pistons in the brakes in place.
    • Test the brakes in your driveway before taking the car onto the road.
    • Set your rotors by evenly braking from 30mph to 10mph, 50mph-30mph and finally 70mph to 40mph.
    • This is best done on a straight back road without any traffic.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Large Hammer
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • M10 x 7cm bolts
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
0
0
brake parts
Ordered front & rear brake pads for my 2004 GMC.
Parts arrived on time. Installed them the next day with no problems & everything works great. Highly recommend 1A for parts. I have ordered other parts from them & they have always delivered.
February 17, 2018
Purchased
2 months ago
Front and rear brake pads
I didn’t know how easy it was to do a brake job. How much money have I wasted thru the years on labor and parts and fees. Not to mention the feeling of a job well done. Great pads and braking. Thanks 1Aauto.
October 21, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2004-2005 Buick Rainier Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2004-2005 Chevy SSR Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2002-2005 Chevy Trailblazer Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2002-2005 Chevy Trailblazer EXT Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2002-2005 GMC Envoy Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2002-2005 GMC Envoy XL Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2004-2005 GMC Envoy XUV Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2003-2006 Isuzu Ascender Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2002-2004 Olds Bravada Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto
  • 2005 Saab 9-7X Front & Rear Brake Pads Premium Posi Semi-Metallic Nakamoto

This part replaces:

  • Nakamoto MD883, MD882
Part #: 1ABFS02020

Ships Same Day for orders placed by 4 P.M. ET

Nakamoto
Brand #: MD883, MD882

How-to Video:

(11:30 min)