This rear brake pad set is just what you need to get your vehicle stopping in good order again!

Specifications:

  • Professional grade Ceramic Enhanced brake pads
  • 4 Piece REAR brake pad set
  • Includes shims
  • Direct replacements

This brake pad set makes a great replacement and has an excellent value over the price of dealer brake pads.

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quite braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:54)
    • Loosen the five 22mm lug nuts with a breaker bar
    • Raise and support the vehicle
    • Remove the lug nuts
    • Slide the wheel off the hub
  2. step : Removing the Brakes (1:26)
    • Place a wrench on one wheel stud to counterhold the brake rotor
    • Remove the T30 Torx screw from the brake rotor
    • Remove the two 14mm guide bolts from the caliper
    • Pull the caliper off its bracket
    • Hang the caliper aside with a bungee cord
    • Pry the brake pads from the caliper bracket with a flat blade screwdriver
    • Remove the two 16mm bolts from the caliper bracket
    • Make sure the emergency brake is off
    • Hit the rotor hub with a hammer to loosen it
    • Pull off the brake rotor
  3. step : Preparing the Brakes (3:35)
    • Pry the brake shims out of the caliper bracket with a flat blade screwdriver
    • Clean the brake shims with a wire brush
    • Clean the caliper bracket with a wire brush
    • Apply brake grease to the caliper bracket
    • Slide the caliper pins out of the caliper bracket
    • Clean the old grease off the caliper pins
    • Apply brake grease to the caliper pins
    • Slide the pins into the caliper bracket
    • Snap the shims onto the caliper bracket
    • Apply grease to the shims
    • Clean the hub surface with a wire brush
    • Apply brake grease to the hub surface
  4. step : Installing the Brakes (7:06)
    • Slide the rotor onto the hub backwards
    • Spray the back of the rotor with brake cleaner
    • Slide the rotor off the hub
    • Slide the rotor onto the hub normally
    • Spray the front of the rotor with brake cleaner
    • Install the T30 screw into the rotor
    • Put the caliper bracket into place
    • Start the two 16mm bolts into the caliper bracket
    • Tighten the two 16mm bolts to 30 foot-pounds of torque
    • Tighten the 16mm bolts an additional 90 degrees
    • Install the brake pads into the caliper bracket
    • Apply brake grease to the back of each brake pad
    • Remove the bungee cord from the caliper
    • Compress the caliper piston with pliers
    • Slide the caliper onto the bracket
    • Install the two 14mm bolts into the caliper
    • Tighten the two 14mm bolts to 20 foot-pounds
  5. step : Installing the Wheel (10:16)
    • Slide the wheel onto the hub
    • Start the five 22mm lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 140 foot-pounds in a star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Brake Parts Cleaner

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 16mm Socket
  • 14mm Socket
  • 22mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Bit

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Rear pads
They were a perfect fit. Easy to install. And are working great.
February 6, 2018
Purchased
2 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2008-2014 Cadillac CTS Rear Premium Posi Ceramic Brake Pads Nakamoto
  • 2010-2016 Cadillac SRX Rear Premium Posi Ceramic Brake Pads Nakamoto
  • 2010-2015 Chevy Camaro V6 3.6L Rear Premium Posi Ceramic Brake Pads Nakamoto

This part replaces:

  • Nakamoto CD1337
Part #: 1ABPS00611

Ships Same Day for orders placed by 4 P.M. ET

Nakamoto
Brand #: CD1337

How-to Video:

(10:49 min)