Specifications:

  • Premium Posi Semi-Metallic brake pads
  • 4 Piece Front brake pad set
  • Includes shims
  • Direct replacement

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quite braking
Positive Mold Technology

Improves durability and performance by allowing for even wear. Eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

Reduces noise and vibration

Environmentally Compliant

Meets the Better Brake Law standards

Part Details

  • Front or Rear Location: Front
  • Brake Pad Friction Material: Semi-Metallic
  • Brake Pad Bonding Type: Premium Posi

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:07)
    • Pry off the lug nut cover
    • Loosen the lug nuts.
    • Raise and secure the vehicle.
    • Remove the lug nuts and the tire.
  2. step : Remove the calipers (1:42)
    • Use your 1/2" socket and ratchet to remove the caliper bolts
    • Use a flat blade screwdriver or pry bar to compress the caliper pistons
    • Pry the caliper of the rotor.
    • Remove the two 15 mm caliper bracket bolts.
  3. step : Replace the rotor (4:21)
    • Pry off the grease cap.
    • Use your pliers to remove the cotter pin.
    • Remove the 27 mm nut.
    • Pull the rotor off.
    • Insert the outside bearing race.
    • Use your race installation tools to tap the race into place.
    • Install the interior race.
    • Apply bearing grease to the races.
    • Pack the interior bearing with bearing grease.
    • Use a paper towel to keep your race tools tidy and install the interior bearing.
    • Apply grease to the exterior race.
    • Clean the spindle and mount the rotor.
    • Install the exterior bearing and apply bearing grease.
    • Put the nut and washer on, and tighten it with your socket and ratchet to seat the bearing.
    • Spin the rotor and loosen the nut and then tighten it again.
    • Do this till the bearing is seated, then put the cotter pin through.
    • Replace the dust cap.
  4. step : Install the calipers (15:20)
    • Mount the caliper bracket and secure it with your 15 mm socket and ratchet
    • Torque these bolts to 80 ft lbs.
    • Compress the caliper with a C-Clamp
    • Apply anti-seize grease to the edges of the brake pads and insert them into the brackets.
    • Mount the calipers to the brackets and torque the bolts to 15 ft lbs.
  5. step : Put the wheel on (18:05)
    • Thread the lug nuts on.
    • Wiggle the wheel to make sure there isn't any play in the bearings.
    • Lower the vehicle
    • Torque the lug nuts to 100 ft lbs.

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 27mm socket
  • 15mm Socket
  • 19mm Socket

  • Sockets - SAE

  • 1/2 Inch Socket

  • Specialty Tools

  • Race Installation Tools

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
good transaction
October 17, 2013
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-2001 Ford Explorer Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 1995-2002 Ford Ranger Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 1995-1997 Mazda B2300 Truck Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 2001-2002 Mazda B2300 Truck Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 1998-2001 Mazda B2500 Truck Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 1995-2002 Mazda B3000 Truck Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 1995-2002 Mazda B4000 Truck Front Premium Posi Semi-Metallic Brake Pads Nakamoto
  • 1997-2001 Mercury Mountaineer Front Premium Posi Semi-Metallic Brake Pads Nakamoto

This part replaces:

  • Nakamoto MD652
Part #: 1ABPS00009

Nakamoto
Brand #: MD652

How-to Video:

(19:32 min)