Brake Pad Specifications:

  • Premium Ceramic brake pads
  • 4 Piece Front brake pad set
  • Direct replacement

Brake Hardware Specifications:

  • Includes both LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Brake Rotor Specifications:

  • Comes as a matched pair
  • Includes both LH (Driver Side) & RH (Passenger Side) Front
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 5 Stud Wheels
  • Studs already installed

Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Reassemble the bearings. (0:30)
    • Use race installation tools or a block of wood to assemble the inner bearing.
    • Pack the outer bearing with bearing grease.
    • Inspect the spindle and clean it with a paper towel.
    • Mount the rotors and insert the outer bearing.
    • thread your washer and bolt on.
    • Tighten the bolt some with your ratchet and then loosen it; this will seat the outer bearing.
    • Put the nut and dust cap on.
  2. step : Install the new brakes (5:09)
    • Clean the brake rotors with brake cleaner.
    • Clean the caliper sleeves with a wire brush.
    • Apply anti-seize grease to the edges of the brake pads where they slide into the calipers.
    • Compress your caliper pistons with a large C-Clamp
    • Put the brake pads into the caliper.
    • Mount the caliper.
    • Clean up your caliper bolts and apply a little anti-seize grease to them.
    • Torque the caliper bolts to 45 ft lbs.
  3. step : Put the wheel back on (8:53)
    • Thread the lug nuts on
    • Lower the vehicle
    • Torque the lug nuts in a star pattern to 100 ft lbs

Tools needed for replacement:

    Allen Wrenches

  • 3/8 Inch Allen Wrench

  • General Tools

  • Jack Stands
  • Hammer
  • Wire Brush
  • Floor Jack
  • Large C-Clamp

  • Materials, Fluids, and Supplies

  • Paper Towels
  • Block of Wood
  • Anti-Seize Grease
  • Brake Parts Cleaner
  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Slip-Joint Pliers

  • Ratchets & Related

  • Torque Wrench

  • Sockets - Metric

  • 19mm Socket
  • 27mm socket

  • Specialty Tools

  • Race Installation Tools

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997 Chevy Blazer S10 Front Ceramic Brake Kit for Models with Rear Drum Brakes 2 Wheel Drive Cross Drilled & Slotted Zinc Coated Performance
  • 1998-2002 Chevy S10 Pickup 2 Wheel Drive Front Brake Kit Ceramic Cross Drilled & Slotted Zinc Coated Performance
  • 1997 GMC Jimmy S-15 Front Ceramic Brake Kit for Models with Rear Drum Brakes 2 Wheel Drive Cross Drilled & Slotted Zinc Coated Performance
  • 1998-2003 GMC S-15 Sonoma 2 Wheel Drive Front Brake Kit Ceramic Cross Drilled & Slotted Zinc Coated Performance
  • 1997 Isuzu Hombre Front Brake Kit Ceramic 2 Wheel Drive Cross Drilled & Slotted Zinc Coated Performance
  • 1998-2000 Isuzu Hombre 2 Wheel Drive Front Brake Kit Ceramic Cross Drilled & Slotted Zinc Coated Performance
Part #: 1APBS00682

Out of Stock

How-to Video:

(09:53 min)