Brake Shoe Specifications:

  • Comes as a set of 4 shoes
    • Fits both LH (Driver Side) & RH (Passenger Side) Rear
  • Premium Grade Brake Shoes
  • Direct replacement
  • For models with 10" drums

Brake Drum Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver) & RH (Passenger Side) Rear
  • Replaces dealer part numbers: 6L5Z 1126 A, 6L5Z1126A, 6L54 1126 AA, 6L541126AA
  • Direct replacement
  • 5 wheel stud holes
  • Drum Size: 10 x 2-1/2 Inches
    • Does not fit 9 x 1-3/4 Drum Size

Wheel Cylinder Specifications:

  • Comes as a Pair
  • Includes LH (Driver Side) & RH (Passenger Side) Rear
  • Cast Iron Construction
  • Direct replacement
  • Built to strict quality control standards

Brake Hardware Specifications:

  • Includes both LH (Driver Side) & RH (Passenger Side) Rear
  • Direct replacements
  • Built to strict quality control standards
100% CNC-Machined to Exact OE Specs

100% CNC-Machined to exact OE specs and balanced to reduce vibration

Cast from OE Grade Alloy

Manufactured from OE Grade G3000 Casting Alloy

Non-Directional Surface Finish

Non-Directional Rotor Surface Finish helps ensure smoother, quieter, and more effective braking

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:00)
    • Pry off the center cap with a flat blade screwdriver
    • Remove the wheel lock lug nut with a wheel lock key
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Drum (1:50)
    • Pull off the drum
    • Tap around the edges and in between the studs if necessary
    • Remove the wheel on the opposite side
  3. step : Removing the Brake Shoes (2:32)
    • Remove the upper brake shoe springs with the vise grip pliers
    • Remove the e-brake cable eyelit
    • Remove the upper plate from the pin
    • Remove the springs and rocker plate the rest of the way
    • Remove the left brake shoe spring with the vise grip pliers
    • Twist off the pin with the vise grip pliers
    • Remove the left brake shoe
    • Twist off the rear retaining spring with the vise grip pliers
    • Twist off the pin with the vise grip pliers
    • Pry the emergency brake cable out of the brake shoe
  4. step : Removing the E-brake Actuator (5:04)
    • Remove the adjustor
    • Remove the spring
    • Pry off the horseshoe clip with pliers
  5. step : Installing the E-brake Actuator (7:30)
    • Insert the spring washer onto the brake shoe
    • Insert the horseshoe clip to the e-brake
    • Crimp the ends of the horseshoe clip
    • Install the spring and adjustor to the shoe
  6. step : Installing the New Brake Shoes (8:37)
    • Clean the backing plate friction points with a wire brush
    • Apply white grease to the friction points
    • Lift the left brake shoe into place
    • Thread the retaining pin into the brake shoe
    • Twist on the retaining spring with vise grip pliers
    • Install the spreader bar with the spring facing the right brake shoe
    • Put the right brake shoe into place
    • Thread the retaining pin into the brake shoe
    • Twist on the retaining spring with vise grip pliers
    • Push the brake shoes together by hand
    • Insert the plate into place
    • Insert the pivot to the brake shoe hole and hook the longer spring to it
    • Connect the eyelit
    • Hook the longer springs on with the vise grip pliers
  7. step : Installing the New Brake Drum (12:40)
    • Try to slide the brake drum on
    • If necessary turn the adjuster wheel with a flat blade screwdriver
    • The brake rotor should slide on with some resistance
  8. step : Reattaching the Wheel (13:44)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds of torque in a crossing or star pattern
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket

5.0 / 5.0
2 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
0
0
0
0
Excellent value!
Excellent value! Good quality parts worked great!Saved quite a bit of money purcashing this. Also came in 3 days!
March 31, 2017
Purchased
1 year ago
rear brake kit 2004 ranger 2wheel drive
i will recommend this to all my friends .great service and arrived 3business days complete.
November 1, 2017
Purchased
6 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1998-2009 Ford Ranger with 10 Inch Drums Rear Brake Kit
  • 2001-2009 Mazda B2300 Truck with 10 Inch Drums Rear Brake Kit
  • 1998-2001 Mazda B2500 Truck with 10 Inch Drums Rear Brake Kit
  • 1998-2007 Mazda B3000 Truck with 10 Inch Drums Rear Brake Kit
  • 1998-2009 Mazda B4000 Truck with 10 Inch Drums Rear Brake Kit
Only 3 left in stock
Part #: 1ABFS02561



How-to Video:

(14:42 min)