Replaces

Brake Kit Nakamoto MD1083, MD1012, 54109-DSZ, 54111-DSZ - 1APBS00319

Part Details

  • Brake Pad Bonding Type: Premium Posi
  • Front Brake Rotor Specifications:
    Vented
    6 Lug
    12.99" (330mm)
  • Brake Pad Friction Material: Semi-Metallic
  • Brake Rotor Type: Cross Drilled & Slotted
  • Brake Rotor Coating: Zinc Coated
  • Kit Includes:
    (1) Rear Semi-Metallic Brake Pad Set
    (1) Front Semi-Metallic Brake Pad Set
    (2) Front Performance Brake Rotors
    (2) Rear Performance Brake Rotors
  • Rear Brake Rotor Specifications:
    13.70" (348mm)
    6 Lug
    Solid
  • Product Line: Performance
  • Brake Pad Features & Benefits:
    OE Grade Multi-Layer Shim
    Positive Mold Technology
    Environmentally Compliant

This performance brake rotor & pad set is just what you need to get your vehicle stopping in good order again!

Brake Pad Specifications:

  • Premium Posi Semi-Metallic brake pads
  • 8 Piece Front & Rear brake pad set
  • Includes shims
  • Direct replacement

Brake Rotor Specifications:

  • Comes as a set of 4
    • Includes both LH (Driver) & RH (Passenger) Side FRONT & REAR
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 6 Stud Wheels
  • Front
    • 12.99" diameter
    • Vented
  • Correct for 4WD models only

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking
Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:41)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:08)
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
  3. step : Removing the Brake Pads and Rotor (1:33)
    • Remove the two 10mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Pull the rotor off
    • Pry the brake pads off the caliper with a flat blade screwdriver
    • Clean the friction areas with a wire brush
    • Clean the slides with a wire brush
    • Pry off the brake pad slides with a flat blade screwdriver
    • Tap the slides on with a hammer
    • Apply white grease to the slides
  4. step : Installing the Brake Pads and Rotors (5:02)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Slide the rotor on
    • Adjust the emergency brake, if necessary, by turning the star wheel with a flat blade screwdriver
    • Install the new brake pads into the caliper
    • Put the caliper on
    • Thread the two 10mm bolts by hand
    • Tighten the 10mm bolts to 17 foot-pounds
  5. step : Reattaching the Wheel (7:11)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 120 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  6. step : Testing the Brakes (7:35)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Wire Brush
  • Large C-Clamp
  • Chisel
  • Hammer
  • Jack Stands
  • Floor Jack

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 10mm Socket

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
My first time ordering on line
You're how to videos are great. I was a little optimistic about ordering auto parts on line but I thought I would give it a try. I must say I was totally satisfied. All parts fit like factory parts and I saved a lot of money. I will definitely use 1A Auto the next time I need auto parts.
July 10, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 3 answers
Will this product fit a 2004 ford f150 xlt 2wd?
Miguel H on Oct 15, 2016
BEST ANSWER: It fit a 2006 4x4. Not sure on the 2wd. Best pad and rotor set I bought.
Do they come with the brake shoes and hardware springs ?etc.my truck has rotors with drums also and I will need brake shoes and hardware thanks
Steve F on Apr 23, 2017
BEST ANSWER: No these are just the brake rotors and pads.

Vehicle Fit

Year Make Model Description
2004Ford F150 Truck Ford F150 Truck New Body Style 4 Wheel Drive 6 Lug Wheels Front & Rear Premium Posi Semi-Metallic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto
2005-2008Ford F150 Truck Ford F150 Truck 4 Wheel Drive 6 Lug Wheels Front & Rear Premium Posi Semi-Metallic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto
2006-2008Lincoln Mark LT Lincoln Mark LT 6 Lug Wheels Front & Rear Premium Posi Semi-Metallic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto

This part replaces:

  • Nakamoto MD1083, MD1012, 54109-DSZ, 54111-DSZ
Part #: 1APBS00319


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: MD1083, MD1012, 54109-DSZ, 54111-DSZ

How-to Video:

(08:07 min)