Replaces

Brake Kit Nakamoto CD883, CD1169A, 55150-DSZ, 55151-DSZ - 1APBS00444

Brake Pad Specifications:

  • Premium Posi Ceramic Disc Brake Pads
  • 8 Piece Front & Rear Brake Pad Set
  • Direct replacement

Brake Rotor Specifications:

  • Comes as a Set of 4
    • Includes both LH (Driver) & RH (Passenger) Side Front & Rear
  • Cross drilled, Slotted, And Zinc Coated
  • Fit 6 Lug Wheels
  • Direct replacements

 

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Remove wheel. (1:15)
    • Remove hub cap or center cap if you have it.
    • While your car is still on the ground, use your 19mm socket to loosen your lug nuts.
    • Jack up and secure your car with jack stands.
    • Remove the lug nuts with your 19mm socket and ratchet.
    • Remove the wheel and set aside.
  2. step : Remove the rear brake calipers (1:46)
    • Use a screwdriver to force the pistons back in.
    • Remove the two 14mm bolts to remove the calipers.
    • Use a wire tie to fasten the caliper out of the way.
    • Use your screwdriver to pry out your brake pads.
    • Remove the two 18mm bolts on the caliper bracket to remove it.
    • Remove the caliper bolt sleeves.
    • Check their condition and clean them with a wire brush if necessary.
    • Pull off the brake rotor.
    • Screw in the two 10M bolts to remove the rotor.
    • Take care not to damage the lug studs.
  3. step : Install new rear brake rotor and pads (6:30)
    • Clean new rotor with brake cleaner.
    • Insert your new pads into the brackets.
    • Put your caliper bracket back on, and tighten the bolts to 90-100 ft lbs.
    • Compress the caliper piston with a c-clamp to reset the pistons.
    • Mount the caliper on the bracket and torque the bolts in to 15-20 ft lbs.
  4. step : Put the rear wheel back on (10:25)
    • Make sure to use a star pattern when putting your wheel lugs back on.
    • Tighten to 100 ft lbs.
    • Replace hubcap/center cap.
  5. step : Test and set brakes (11:00)
    • Before driving the car again, start it up and pump the brakes a few times to get the pistons in the brakes in place.
    • Test the brakes in your driveway before taking the car onto the road.
    • Set your rotors by evenly braking from 30mph to 10mph, 50mph-30mph and finally 70mph to 40mph.
    • This is best done on a straight back road without any traffic.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large C-Clamp
  • Large Hammer
  • Rubber Mallet

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • M10 x 7cm bolts
  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 14mm Socket
  • 18mm Socket
  • 19mm Socket

5.0 / 5.0
4 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
4
0
0
0
0
very good parts
I installed them in my 2009 gmc acadia and fixed my breaking problems
April 11, 2018
Purchased
1 month ago
Brake kit
I called to make sure this was the right one for my vehicle they were very helpful and knowledgeable the kid fit perfectly looks and performs very well I will be ordering more parts from A1 auto you can’t beat the prices
April 16, 2018
Purchased
3 weeks ago
Great Price! Super upgrade to the factory Rotors and Pads
Products were spot on replacements and after this upgrade will not be going back to solid rotors.
March 21, 2017
Purchased
1 year ago
Brakes and rotors kit
Great product, fast delivery. Will order from them again and in the future. Love the diy video very informative.
July 27, 2017
Purchased
9 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Will these work for the 19inch wheel option on my 2008 gmc acadia slt?
Jeff S. on Jun 23, 2017
BEST ANSWER: Yes, as long as you have the OE size brakes.

Vehicle Fit

  • 2008-2016 Buick Enclave Front & Rear Premium Posi Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto
  • 2009-2016 Chevy Traverse Front & Rear Premium Posi Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto
  • 2007-2016 GMC Acadia Front & Rear Premium Posi Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto
  • 2007-2010 Saturn Outlook Front & Rear Premium Posi Ceramic Cross Drilled & Slotted Zinc Coated Performance Brake Kit Nakamoto

This part replaces:

  • Nakamoto CD883, CD1169A, 55150-DSZ, 55151-DSZ
Part #: 1APBS00444

Out of Stock

Nakamoto
Brand #: CD883, CD1169A, 55150-DSZ, 55151-DSZ

How-to Video:

(11:30 min)