Replaces

Brake Kit Nakamoto CD679, CD711, 54092-DSZ, 54090-DSZ - 1APBS01024

Brake Pad Specifications:

  • Premium Posi Ceramic brake pads
  • 8 Piece Front & Rear brake pad set
  • Includes shims
  • Direct replacement

Brake Rotor Specifications:

  • Comes as a set of 4
    • Includes both LH (Driver) & RH (Passenger) Side Front & Rear
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 5 Lug Wheel
  • 12.13" (308mm) diameter vented front
  • 13.15" (334mm) diameter solid rear

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking

Note:
The rotors do not include wheel bearings or seals.

Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:25)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:06)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the 10mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the brake pad slides
  3. step : Removing the Brake Drum (2:29)
    • Tighten a lug nut to the hub
    • Tap the drum to loosen it
    • Remove the lug nut
    • Pull the drum off
  4. step : Installing the New Brake Drum (3:57)
    • Slide the drum on
    • Thread on one lug nut to hold the drum in place
    • Adjust the emergency brake, if necessary
    • Clean the drum with brake parts cleaner or mineral spirits
  5. step : Installing the New Brake Pads (4:57)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Apply grease to the back of the pads and their contact point on the cast iron
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Tighten the caliper bolts
    • Remove the lug nut from the hub
  6. step : Reattaching the Wheel (7:25)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Hammer

  • Materials, Fluids, and Supplies

  • Bungee Cord
  • Anti-Seize Grease
  • Mineral Spirits

  • Ratchets & Related

  • Socket Extensions
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 19mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
front rotors come with bearings and seals ?
Jim H on Jun 17, 2017
BEST ANSWER: These front rotors do not include bearings or seals.

Vehicle Fit

  • 2004 Ford F150 Heritage Truck Front & Rear 2 Wheel Drive Cross Drilled & Slotted Zinc Coated Premium Posi Ceramic Brake Kit for Models with 5 Lug Wheels (excluding Lightning Models) Performance Nakamoto
  • 1999 Ford F150 Truck Front & Rear 2 Wheel Drive Cross Drilled & Slotted Zinc Coated Premium Posi Ceramic Brake Kit for Models with 5 Lug Wheels 14mm Wheel Stud Size (Built After 11/28/99 Production Date) Performance Nakamoto
  • 2000-2003 Ford F150 Truck Front & Rear 2 Wheel Drive Cross Drilled & Slotted Zinc Coated Premium Posi Ceramic Brake Kit for Models with 5 Lug Wheels (excluding Lightning Models) (excluding Crew Cab) Performance Nakamoto
  • 2002 Lincoln Blackwood Front & Rear Cross Drilled & Slotted Zinc Coated Premium Posi Ceramic Brake Kit Performance Nakamoto

This part replaces:

  • Nakamoto CD679, CD711, 54092-DSZ, 54090-DSZ
Part #: 1APBS01024

Out of Stock

Nakamoto
Brand #: CD679, CD711, 54092-DSZ, 54090-DSZ

How-to Video:

(08:14 min)