Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the front brakes on this 2000 Chevy Cavalier. It's pretty much the same as any Cavalier from this generation. We're going to show you the right hand or passenger side. The left hand, the driver's side's, the same, and we always recommend you service your brakes in pairs. For these front brakes you'll need new pads and rotors from 1AAuto.com, jack and jack stands, 19 millimeter socket with a breaker bar, 3/8 inch Allen wrench with a pipe for some leverage, a large screwdriver or a small pry bar, a large C-clamp, brake or white grease, and a torque wrench.
Use the 19 millimeter socket to loosen the caps. This vehicle has a wheel cover, so you loosen the caps first, and then you can pull the wheel cover off and then with the same 19 millimeter socket, you'll probably want to loosen the lug nuts with the wheel on the ground. Then raise and support the vehicle, and remove the lug nuts the rest of the way, and remove the wheel and tire.
Now turn the wheel so you have easy access to the brakes. Check on the brake conditions. See the inner pad has plenty of life left. It's the same with the outer. Then, you check the condition of the rotors. Run the back of your finger along the outside, as well as the inside. Make sure they're nice and smooth and no deep grooves or anything. These brakes are in fine shape so we'll just take them apart and put them back together to show you.
Two 3/8 Allen bolts hold the caliper to the caliper bracket. I've got a 3/8 Allen key, and then I just use a pipe, or you could use another wrench, and use a little bit of extra leverage and get the bolt started. Here I'll just fast forward as we remove those bolts the rest of the way. Use a large screwdriver or pry bar and pry the caliper out. That forces the piston back in some and gives you extra room just to be able to pull the caliper right up and off. The inner pad's just held in with a couple clips. It pulls out towards the outer pad and then up and out. Then the outer pad is held in with more sturdy clips. Actually what you need to do is force the pad away from the caliper, and then pry it up and bring it up and out of the caliper.
The rotor should come right off. Use a hammer if you need to.
Now we're going to use a large C-clamp to reset the piston and the caliper. You can see, as we tighten the clamp, it forces the piston back in. We did detect some uneven wear on the pads, so we're going to force the bolts out. So, Don just uses the 3/8 Allen wrench, kind of twists them back and forth, and pulls on the bolts. You push on one end with your thumb as you're twisting it back and forth, and then grab the other end and pull them right out. We'll use some white grease. We basically took a wire brush, cleaned them up a little bit first, and then took some white grease, put it on there, and then they should slide right back into the caliper nice and easy. Reinstall the rotor. The rotors from 1A Auto are going to fit just like the original. You can see we are just reinstalling the original because, like I said, they're in good shape.
Put a little bit of grease on the backside of the inner pad, and then fit that down into the caliper, and snap the clips into the piston. Do the same thing, put a little bit of grease on the outer pad. The grease just keeps them from squeaking a little bit. It's a little bit of insurance against that. Then, snap that outer pad down in. Just make sure your pad stays put and then put the assembly right down on. Then, use your 3/8 Allen wrench and start the bolts in. I'll fast forward here as we take care of tightening those up. Those bolts should be tightened up to about 30 to 35 foot-pounds.
Turn the wheels back straight, put the wheel and tire back on, install the lug nuts by hand first, and then tighten them preliminarily. Put the vehicle back down on the ground. Tighten the lug nuts to 100 foot-pounds using a star pattern to tighten them. Then put your hub cap or whatever back on, and just tighten those plastic nuts with the socket itself by hand.
Last but not least, always make sure you pump the brake, get a nice firm pedal before road testing.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
