Brake Pad Specifications:

  • 4 Piece Front Brake Pad Set
  • Includes shims
  • Direct replacements
  • Professional Grade Ceramic Enhanced Disc Brake Pads

Brake Rotor Specifications:

  • Comes as a Pair
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Fits 5 Stud Wheels
  • Vented
  • 11.65" (296mm) diameter

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a Pair
    • Fits both LH (Driver Side) & RH (Passenger Side) Front
  • Includes hubs and bearings as shown
  • Fits 5 Lug Wheels
  • Studs already installed onto hubs
  • Direct replacements
  • Built to strict quality control standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:52)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle Nut (1:22)
    • Insert a wrench onto a spline, angled toward the inside of the vehicle
    • Thread a lug nut over the wrench
    • Rotate the hub so the wrench is pressed to the caliper
    • Remove the T30 Torx bolt
    • Lower the vehicle to the ground
    • Remove the 35mm axle nut
    • Raise the vehicle
    • Remove the wrench and lug nuts
    • Insert a flat punch into the divet in the center of the axle
    • Hammer the punch to tap the splines free
  3. step : Removing the Caliper Bracket (3:31)
    • Remove the two 18mm bolts from the caliper bracket
    • Pull the caliper off
    • Put the caliper aside
    • Remove the rotor
  4. step : Removing the Hub Assembly (4:28)
    • Clean off the hub with a wire brush and rust penetrant
    • Disconnect the ABS sensor connector
    • Remove the 15mm bolts from the back of the hub
    • Remove the wheel hub and bearing
  5. step : Installing the Hub Assembly (8:20)
    • Clean off any build up and debris from the hub surface with a wire brush
    • Insert the wheel hub into the spindle
    • Tighten the 15mm bolts
    • Torque the bolts to 96 foot-pounds
    • Reconnect the ABS sensor
  6. step : Installing the Brake Rotor (10:52)
    • Apply grease to the hub surface
    • Put the rotor onto the hub backwards
    • Spray the rear of the hub with brake cleaner
    • Pull off the brake rotor
    • Slide the brake rotor on
    • Spray the front of the rotor with brake cleaner
    • Put the caliper bracket into place
    • Insert the two 18mm bolts into the caliper bracket
    • Tighten the two 18mm bolts to 137 foot-pounds of torque
  7. step : Reinstalling the Axle Nut (11:55)
    • Insert a wrench onto a spline, angled toward the inside of the vehicle
    • Thread a lug nut over the wrench
    • Rotate the hub so the wrench is pressed to the caliper
    • Tighten the axle nut with a 35mm socket and ratchet
    • Torque the nut to 151 foot-pounds
    • Pop out the center cap on the wheel
  8. step : Reattaching the Wheel (12:41)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 35mm Socket
  • Complete Metric Socket Set

  • Torx Drivers & Sockets

  • T30 Torx Bit

  • Wrenches - Metric

  • Complete Metric Wrench Set

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
review
got my product in the time that was i was told, fits my car great and now my car is safe to drive again
February 6, 2018
Purchased
1 month ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 4 answers
The description says "Buyer will need to press bearings onto hubs" but the pictures appear to show bearings already in the hubs - which is correct?
Randy R on Sep 24, 2016
BEST ANSWER: Mine (1ABMS00066-Brake Pad Rotor & Wheel Bearing Kit) was complete. The hub came with the bearing & the ABS cable.

How-to Video:

(13:16 min)

Tools List:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Anti-Seize Grease
  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Sockets - Metric

  • 35mm Socket
  • Complete Metric Socket Set

  • Torx Drivers & Sockets

  • T30 Torx Bit

  • Wrenches - Metric

  • Complete Metric Wrench Set



This part replaces:

  • Hollander 530-00123
  • OE # 19206599, 4342178J01
  • Hollander 538-00123
  • Hollander 538-00178
  • Hollander 538-50220
  • OE # 434217800
  • Hollander 530-50211
  • Reference Number CD1264
  • Reference Number 900320

Vehicle Fit

  • 2007-2009 Chevy Equinox Front Brake & Wheel Bearing Kit Ceramic
  • 2007-2009 Pontiac Torrent Front Brake & Wheel Bearing Kit Ceramic
  • 2008-2010 Saturn Vue Front Brake & Wheel Bearing Kit Ceramic
  • 2007-2009 Suzuki XL-7 Front Brake & Wheel Bearing Kit Ceramic
Part #: 1ABMS00054

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More