Brake Pad Specifications:

  • Premium Posi Ceramic Enhanced Disc Brake Pads
  • Fits FRONT Rotors
  • 4 Piece Brake Pad Set
  • No core charge
  • Includes shims

Brake Rotor Specifications:

  • Comes as a PAIR
    • Fits LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 19181002
  • Fit 6 Stud Wheels
  • 11.9" Diameter Vented Rotors

Wheel Bearing & Hub Assembly Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 12413037, 15130858
  • Includes lug nut studs already installed, ABS Sensors, and ABS Sensor Wire Harnesses
  • 3 Bolt Flanges
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Thermal Scorched

Pre-burnishing or "Thermal Scorching" is the final curing step in quality ceramic brake pad manufacturing. The brake pad's surface is heated to remove any uncured bonding agents and to stabilize the friction material to accelerate the break-in process and enhance stopping performance from the first stop.

100% CNC-Machined to Exact OE Specs

100% CNC-Machined to exact OE specs and balanced to reduce vibration

Cast from OE Grade Alloy

Manufactured from OE Grade G3000 Casting Alloy

Non-Directional Surface Finish

Non-Directional Rotor Surface Finish helps ensure smoother, quieter, and more effective braking

Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Step 1: Remove the wheel and tire (1:18)
    • Raise and secure the vehicle.
    • Remove the lug nuts and then the wheel.
  2. step : Step 2: Remove Caliper (2:07)
    • Turn wheels all the way in the opposite direction of the side you are working on.
    • Use your 13mm socket wrench to remove the caliper bolts.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your 18mm socket to remove the brackets.
  3. step : Step 3: Remove brake disk (4:13)
    • Take care not to touch the disk, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  4. step : Step 4: Remove Hub (4:42)
    • Use a 35mm socket to remove the hub nut.
    • Give the axle a slight tap with a hammer to loosen it.
    • Remove the 3 bolts securing the hub using your 18mm socket and extension and ratchet or breaker bar.
    • You can use penetrating oil to help.
    • Disconnect your ABS sensor.
    • Use a rubber mallet to break your hub free, and work around the flange with the hammer to pull it off.
    • Remove the hub and shield.
    • Clean up any corrosion with a wire brush.
  5. step : Step 5: Install new hub (9:10)
    • Use some penetrating oil to prep the knuckle for the new hub.
    • Put the three 18 mm bolts in place and tighten the nuts to 90 ft lbs.
    • Reinstall the ABS harness.
    • Tighten but don't torque the lug nut.
  6. step : Step 6: Put brakes and wheel back on (11:50)
    • Remember to replace the lug nuts on in a star pattern.
    • Lug nuts tighten to 100-120 ft lbs
    • Hub nut is 103 ft lbs.
    • Make sure to check your brakes and steering before driving again.
    • Make sure to pump the brakes and seat your rotors.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Rubber Mallet
  • Wire Brush

  • Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 19mm Socket
  • 35mm Socket

4.7 / 5.0
3 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
2
1
0
0
0
The whole order process worked perfectly. I had the parts in 2 days. Replaced them in 2 hours. The trailblazer rides quiet and smooth now. The brakes scraped bad at first. But it was because I rushed and put 1 brake pad on backwards. What a dumba$$.
March 17, 2018
Purchased
3 months ago
Rotor don't fit
Hub bearing work and fit rotor don't fit need rotors for a 06 trailblazer ext lt
March 6, 2018
Purchased
4 months ago
Wheel bearings bearings and rotors
I would absolutely buy these again.. so far everything ive bought from 1A Auto i am completely satisfied on price and quality.
February 26, 2018
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Do the brakes include hardware ?
Barry M on Dec 22, 2016
BEST ANSWER: The brake hardware used to install the brake pads is not included, but you may reuse the existing hardware or purchase new hardware separately.

Vehicle Fit

  • 2004-2005 Buick Rainier L6 4.2L Front Premium Posi Ceramic Brake & Wheel Bearing Kit
  • 2002-2005 Chevy Trailblazer Front Premium Posi Ceramic Brake & Wheel Bearing Kit
  • 2002-2004 GMC Envoy Front Premium Posi Ceramic Brake & Wheel Bearing Kit
  • 2005 GMC Envoy L6 4.2L Front Premium Posi Ceramic Brake & Wheel Bearing Kit
  • 2003-2005 Isuzu Ascender L6 4.2L Front Premium Posi Ceramic Brake & Wheel Bearing Kit
  • 2002-2004 Olds Bravada Front Premium Posi Ceramic Brake & Wheel Bearing Kit
Part #: 1ABMS00022


How-to Video:

(13:45 min)