Specifications: 

  • Brand New Ball Joint
  • Fits LH (Driver Side) or RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards

Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greasable versions.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (1:14)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Stabilizer Link (1:34)
    • Turn the wheel by hand
    • Hold the upper stabilizer link stud with a 14mm or 9/16 inch wrench
    • Remove the upper nut from the stabilizer link with a 14mm wrench
    • Hold the lower stabilizer link stud with a 14mm or 9/16 inch wrench
    • Remove the lower nut from the stabilizer link with a 14mm wrench
    • Pull off the stabilizer link
  3. step : Removing the Control Arm (3:02)
    • Loosen the lower ball joint nut with a 19mm wrench
    • Strike the wheel spindle with a hammer to loosen the ball joint
    • Remove the two 19mm bolts from the control arm
    • Loosen the 19mm bolts from the control arm bracket
    • Remove the 22mm bolt from the control arm
    • Remove the 19mm nut from the ball joint
    • Pry the control arm off with a pry bar
  4. step : Removing the Ball Joint from the Control Arm (7:08)
    • Tear the boot off the ball joint
    • Break off the metal ring at the base of the ball joint
    • Knock out the ball joint c-clip with a flat blade screwdriver and a hammer
    • Put a 30mm socket over the ball joint
    • Hammer the ball joint out of the control arm using the socket
  5. step : Installing the New Ball Joint into the Control Arm (8:52)
    • Put the new ball joint into the control arm
    • Put a 30mm socket on the back of the ball joint
    • Hammer the ball joint into the control arm with a socket
    • Apply grease to the ball joint
    • Put the c-clip onto the ball joint
    • Put a 36mm socket on the ball joint
    • Hammer in the c-clip with the socket
    • Push the clip in with a flat blade screwdriver and a hammer
    • Apply more grease to the ball joint
    • Put the boot into place
    • Put a 36mm socket on the boot
    • Hammer in the boot with the socket
    • Push the boot in with a flat blade screwdriver and a hammer
  6. step : Reinstalling the Control Arm (12:04)
    • Put the control arm into place, starting at the rear
    • Feed the 22mm bolt into the control arm
    • Push the ball joint into place
    • Thread the 19mm nut onto the ball joint by hand
    • Insert the two 19mm bolts into the control arm
    • Insert the 22mm bolt
    • Tighten the 19mm bolts to 100 - 110 foot-pounds of torque
    • Tighten the 22mm bolt to 130 foot-pounds
    • Tighten the 19mm nut on to the ball joint
  7. step : Reinstalling the Stabilizer Link (14:39)
    • Push the stabilizer link into place
    • Start the 14mm nuts by hand
    • Hold the upper stabilizer link stud with a 14mm or 9/16 inch wrench
    • Fasten the upper nut onto the stabilizer link with a 14mm wrench
    • Hold the lower stabilizer link stud with a 14mm or 9/16 inch wrench
    • Fasten the lower nut onto the stabilizer link with a 14mm wrench
  8. step : Reattaching the Wheel (15:34)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands
  • Large Hammer

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Screwdrivers & Related

  • Pry Bar
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 22mm Socket
  • 30mm Socket
  • 19mm Socket
  • 36mm Socket
  • 14mm Socket

  • Specialty Tools

  • Vise-Grips

  • Wrenches - Metric

  • 19mm Wrench
  • 14mm Wrench

  • Wrenches - SAE

  • 9/16 Inch Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1995-1999Hyundai Accent Hyundai Accent Front Lower Ball Joint Driver or Passenger Side
1996-2006Hyundai Elantra Hyundai Elantra Front Lower Ball Joint Driver or Passenger Side
1989-1994Hyundai Sonata Hyundai Sonata Front Lower Ball Joint Driver or Passenger Side
1997-2001Hyundai Tiburon Hyundai Tiburon Front Lower Ball Joint Driver or Passenger Side
2003-2008Hyundai Tiburon Hyundai Tiburon Front Lower Ball Joint Driver or Passenger Side
2001Hyundai XG300 Hyundai XG300 Front Lower Ball Joint Driver or Passenger Side
2002-2005Hyundai XG350 Hyundai XG350 Front Lower Ball Joint Driver or Passenger Side
2004-2009Kia Spectra Kia Spectra Front Lower Ball Joint Driver or Passenger Side
2005-2009Kia Spectra 5 Kia Spectra 5 Front Lower Ball Joint Driver or Passenger Side

This part replaces:

  • Moog K500031
  • OE # 5453031600
Part #: 1ASBJ00294


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(16:33 min)