Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT LOWER FORWARD
  • Includes new ball joints and bushings
  • Direct fit replacements
  • Built to strict quality control standards

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Skid Plate (1:05)
    • Remove the plastic clips from the skid plate bumper with a flat blade screwdriver
    • Remove the Phillips head screws from the skid plate
    • Pull the skid plate down and off
  2. step : Removing the Wheel (2:06)
    • Remove the center cap with a pick tool
    • Loosen the 17mm lug bolts with the vehicle on the ground
    • Raise and support the vehicle
    • Remove the lug bolts
    • Pull off the wheel and tire
  3. step : Removing the Forward Lower Control Arm (2:39)
    • Soak the control arm bolts in penetrating oil
    • Remove the 16mm bolt from the top of the sway bar link
    • Remove the 18mm bolt from the bottom of the strut
    • Loosen the 18mm bolt at the back of the forward lower control arm
    • Remove the 18mm bolt that connects the forward lower control arm to the wheel spindle
    • Tap a ball joint separator onto the joint with a hammer
    • Tighten the ball joint separator bolt until the ball joint separates
    • Remove the 18mm bolt that holds the forward lower control arm to the chassis
  4. step : Removing a Stubborn Ball Joint (5:06])
    • This step is only necessary if the ball joint cannot be separated with the ball joint separator
    • Remove the 18mm nut from the spindle end of the rearward lower control arm
    • Remove the 18mm bolt from the chassis end of the rearward lower control arm
    • Separate the lower forward control arm ball joint from the spindle with a pickle fork and hammer
    • If necessary, remove the forward lower control arm ball joint with a two jaw puller
    • If the two jaw puller does not work, cut the ball joint stud with a rotary grinder or sawzall
    • If necessary, tap the stud out of the spindle with an air chisel
    • If necessary, separate the sleeve and bolt with a hydraulic press
    • Remove the 18mm bolt that holds the forward lower control arm to the chassis, if you have not done so already
  5. step : Installing the Lower Forward Control Arm (8:10)
    • Start the sleeve into the spindle with a hammer
    • Use a ball joint press to press in the sleeve
    • Heat the sleeve, if necessary
    • Apply Loctite to the edges of the sleeve
    • Put the lower forward control arm into place on the frame
    • Start the 18mm bolt and nut onto the frame side of the lower forward control arm
    • Push the lower forward control arm into the spindle
    • Put the strut to the side
    • Start the 18mm nut onto the spindle side of the lower forward control arm
    • Tighten the 18mm nut to 81 foot-pounds of torque
    • Use a pry bar to slide the strut into place
    • Reinstall the cv axle into the hub, if you have removed it
    • Thread the axle bolt onto the cv axle by hand, if necessary
    • Start the 18mm bolt into the bottom of the strut
    • Put the lower rearward control arm into place
    • Start the 18mm nut onto the lower rearward control arm
    • Tighten the 18mm nut to 81 foot-pounds
    • Insert the 16mm bolt into the sway bar link
    • Lift the spindle to normal ride height with a jack
    • Insert the 18mm bolt into the chassis end of the lower rearward control arm
    • Tighten the 18mm bolt to 52 foot-pounds
    • Tighten the lower forward control arm bolt at the chassis side to 55 foot-pounds
    • Tighten the strut bolt to 66 foot-punds
    • Tighten the sway bar link bolt to 52 foot-punds
    • Lower the jack from the spindle
  6. step : Reinstalling the Wheel (12:57)
    • Start one lug bolt into the wheel
    • Lift the wheel into place
    • Start the first lug bolt by hand
    • Insert the lug bolts into the wheel
    • Lower the vehicle to the ground
    • Tighten the lug bolts to 90 foot-pounds in a crossing or star pattern
    • Using a 17mm Allen socket and a torque wrench torque the axle bolt to 148 foot-pounds
    • Turn the axle bolt an additional 180 degrees
    • Line up the center cap using the slots
    • Push the center cap into place
  7. step : Reinstalling the Skid Plate (14:06)
    • Lift the skid plate into place
    • Insert the plastic fasteners into the skid plate
    • Insert the two Phillips head screws into the skid plate

Tools needed for replacement:

    Air Powered Tools

  • Air Chisel

  • Allen Wrenches

  • 7mm Allen Wrench

  • General Tools

  • Chisel
  • Sawzall
  • Pick
  • Jack Stands
  • Hammer
  • Rotary Tool
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Liquid Thread Locker

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Slip-Joint Pliers

  • Ratchets & Related

  • Torque Wrench
  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 16mm Socket
  • 17mm Socket
  • 13mm Socket

  • Specialty Tools

  • Pickle Fork
  • Ball Joint Press
  • Audi Wheel Cap Removal Tool
  • Acetylene torch

  • Wrenches - Metric

  • 16mm Wrench
  • 17mm Wrench
  • 18mm Wrench
  • 13mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2002Audi A4 Audi A4 Front Lower Forward Control Arm with Ball Joint Pair (8th Vin Digit E)
2003-2008Audi A4 Audi A4 Front Lower Forward Control Arm with Ball Joint Pair
2009Audi A4 Audi A4 Convertible Front Lower Forward Control Arm with Ball Joint Pair
2002Audi A4 Quattro Audi A4 Quattro Front Lower Forward Control Arm with Ball Joint Pair (8th Vin Digit E)
2003-2008Audi A4 Quattro Audi A4 Quattro Front Lower Forward Control Arm with Ball Joint Pair
2009Audi A4 Quattro Audi A4 Quattro Convertible Front Lower Forward Control Arm with Ball Joint Pair
2007-2008Audi RS4 Audi RS4 Front Lower Forward Control Arm with Ball Joint Pair
2004-2008Audi S4 Audi S4 Front Lower Forward Control Arm with Ball Joint Pair
2009Audi S4 Audi S4 Convertible Front Lower Forward Control Arm with Ball Joint Pair
Part #: 1ASFK00852


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(14:48 min)