Replaces

Audi Brake Rotor Pair Nakamoto 34319-DSZ - 1APBR00146

Specifications:

  • Comes as a matched Pair
    • Includes both LH (Driver) & RH (Passenger) Side Front
  • Cross drilled, Slotted, And Zinc Coated
  • Direct replacements
  • Fits 5 Stud Wheels
  • Vented
  • 12.63" (321mm) Diameter

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:44)
    • Remove the center cap with a cap removal tool or pick
    • Loosen the 17mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands evenly on both sides
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:46)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
    • Check for gouges on both sides of the rotor
  3. step : Removing the Brake Pads (2:15)
    • Press the tab and disconnect the brake sensor
    • Remove the two rubber caps
    • Remove 7mm Allen bolts from the brake caliper
    • Pry out the clip on the caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside and wire tie it to the knuckle to relieve brake hose stress
    • Pry the brake pads off with a flat blade screwdriver
    • Remove the brake pad slides
  4. step : Removing the Rotor (4:12)
    • Remove the T30 bolt from the rotor
    • Remove the 21mm bolts on the backside of the rotor
    • Remove bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  5. step : Slide the Rotor On (4:42)
    • Line up and press the rotor in place
    • Tighten the T30 bolt to the rotor
    • Tighten the 21mm bolts to the backside
    • Clean the rotor with brake parts cleaner or mineral spirits
    • Put the caliper bracket back into place
    • Find out if you have M12 or M14 bolts on the backside
    • Tighten the M12 bolts to 96 foot-pounds of torque
    • Tighten the M14 bolts to 148 foot-pounds of torque
  6. step : Installing the New Brake Pads (5:42)
    • Put an old pad in the caliper
    • Use a large C-clamp and the new pad to push the pistons back
    • Install the second brake pad
    • Put the caliper on
    • Reconnect the brake sensor wire
    • Thread 7mm Allen bolts
    • Tighten bolts to 18 foot-pounds
    • Insert the spring to the caliper
  7. step : Reattaching the Wheel (8:46)
    • Slide the wheel into place
    • Start the 17mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 90 foot-pounds in a star pattern
    • Reattach the center cap
  8. step : Testing the Brakes (8:40)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Allen Wrenches

  • 7mm Allen Wrench

  • General Tools

  • Jack Stands
  • Large C-Clamp
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Wire Ties

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 17mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Bit

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(10:01 min)

Tools List:

    Allen Wrenches

  • 7mm Allen Wrench

  • General Tools

  • Jack Stands
  • Large C-Clamp
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Brake Parts Cleaner
  • Wire Ties

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 17mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Bit



This part replaces:

  • Nakamoto 34319-DSZ

Vehicle Fit

  • 2005-2009 Audi A4 Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2005-2009 Audi A4 Quattro Quattro Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2005-2009 Audi A4 Quattro Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 1999-2001 Audi A6 Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2002-2004 Audi A6 Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with ATE Brake System 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 1999-2001 Audi A6 Quattro Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2002-2004 Audi A6 Quattro Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with ATE Brake System 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2002-2004 Audi A6 Quattro Quattro Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with ATE Brake System 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2001-2005 Audi Allroad Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
  • 2000-2002 Audi S4 Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair for Models with 12.64" (321mm) Diameter Rotors Performance Nakamoto
Part #: 1APBR00146

Ships Same Day for orders placed by 4 P.M. ET

Nakamoto
Brand #: 34319-DSZ

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More