Specifications:

  • Brand New Grille
  • Direct replacement 
  • Built to strict quality control standards

48 States Only:

Due to shipping restrictions, we can only ship this to a physical address within the Contiguous U.S. (lower 48 states).

NOTE: It is necessary to reuse your original hardware, as new hardware is not included with this item.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Bumper Cover (0:50)
    • Secure the vehicle on jack and jack stands
    • Turn the three flat blade fasteners underneath the bumper counterclockwise and remove them
    • Optional: To remove the center panel, remove the six Phillips or Torx screws
    • Remove the T25 fasteners inside the wheel well
    • Pull the wheel well out off its studs
    • Remove the two 10mm nuts from both sides of the body panel
    • Remove the three T30 bolts near the top of the grille
    • Loosen the two T30 bolts near the headlights with an extension
    • Remove the fascia
    • Disconnect the fog light wiring harness
    • Remove the bumper cover
  2. step : Removing the Grille (5:45)
    • Remove the T20 screws around the edge of the grille
    • Pry the tab with a flat blade screwdriver to remove the grille
  3. step : Removing the Audi Emblem (6:28)
    • Pry the tabs and pull out the Audi emblem
    • Remove the emblem
  4. step : Reinstalling the Audi Emblem (7:57)
    • Push the old emblem into the new grille
  5. step : Reinstalling the Grille (8:11)
    • Insert the grille to the bumper cover
    • Tighten the T20 Torx screws to the bumper cover
  6. step : Installing the Bumper Cover (8:37)
    • Connect the fog light wiring harness
    • Insert the bumper cover into place
    • Insert the fascia into place
    • Tighten the two T30 bolts near the headlights with an extension
    • Tighten the three T30 bolts near the top of the grille
    • Tighten the six screws to the center panel
    • Press the wheel well guard into place
    • Tighten the T25 fasteners inside the wheel well
    • Tighten the three fasteners underneath the bumper

Tools needed for replacement:

    General Tools

  • Flashlight

  • Ratchets & Related

  • Swivel
  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Bit
  • T20 Torx Driver
  • T25 Torx Driver

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2005 Audi A4 B7 Chrome & Silver Grille (excluding S Line Models)
  • 2006-2008 Audi A4 Chrome & Silver Grille (excluding S Line Models)
  • 2009 Audi A4 Convertible Chrome & Silver Grille (excluding S Line Models)
  • 2005 Audi A4 Quattro B7 Chrome & Silver Grille (excluding S Line Models)
  • 2006-2008 Audi A4 Quattro Chrome & Silver Grille (excluding S Line Models)
  • 2009 Audi A4 Quattro Convertible Chrome & Silver Grille (excluding S Line Models)
  • 2005 Audi S4 B7 Chrome & Silver Grille (excluding S Line Models)
  • 2006-2008 Audi S4 Chrome & Silver Grille (excluding S Line Models)
  • 2009 Audi S4 Convertible Chrome & Silver Grille (excluding S Line Models)

This part replaces:

  • Hollander 104-50236C
  • OE # 8E0853651J1QP
  • Partslink AU1200112
Difficulty:
Time:

1-2 Hours

Part #: 1ABGR00664


How-to Video:

(11:26 min)