Replaces

Air Suspension Kit Arnott SK-2126, AS-2127, P-2793, SK-2760 - ARSFK00016

Compressor Specifications:

  • Brand New Arnott Air Suspension Compressor
    • no core charge
  • Includes compressor, air line, dryer, & relay
  • Complete assembly
  • Includes detailed instructions
  • Durability tested for over 1,000 hours
Front Shock Specifications:
  • Brand New Arnott Electronic Shock Replacement Kit*
  • Includes:
    • LH (Driver Side) & RH (Passenger Side) Front Gas Shocks (to eliminate front air shock)
    • (2) Auto dampening control error code eliminator sensors
  • Direct fit for modles with factory electronic shocks
  • Built to strict quality control standards
  • Correct for models with Autoride suspension
Rear Shock Specifications:
  • Brand New Arnott Electronic Shock Replacement Kit*
  • Includes:
    • LH (Driver Side) & RH (Passenger Side) Rear Gas Shocks
    • (2) Goodyear air spring bladders
  • Integrated Dampening Control Sensors
  • Complete assemblies
  • Direct replacements for factory electronic shocks
  • No modifications necessary
  • Correct for models with Autoride suspension
Arnott's new exclusive design connects to the auto-leveling system with no modifications. Includes sensors to plug into the auto dampening control unit to eliminate any error messages on your dash.

ARNOTT is your source for air shocks and air suspension components for Lincoln, Ford, Cadillac, Lexus and Range Rover. Since 1989, Arnott has been designing and manufacturing quality air struts, compressors (pumps) and air bags (springs). Arnott continues to lead in research and development of new products while maintaining affordable prices.

This item is a passive conversion for models that originally came equipped with an automatic dampening (electronic) suspension.  It will fit just like the original did, bypass the factory sensors, and allow a more consistent ride thanks to a revised gas shock design.

Part Details

  • Quantity: 5 Piece Set
  • Kit Includes: (1) Air Suspension Compressor
  • Kit Includes: (2) Rear Electronic Conversion Air Shocks
  • Kit Includes: (2) Front Electronic Conversion Shock Absorbers

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Air Ride Compressor (0:44)
    • Remove the spare wheel
    • Pull the hose off of the air ride compressor
    • Reset the hose clip
    • Loosen the three 12mm nuts from the compressor
    • Lift the air compressor up and out
    • Disconnect the compressor wiring harness
    • Disconnect the second compressor hose at the chassis
  2. step : Removing the Motor from the Compressor (2:27)
    • Pull the clips out of the compressor cover with a pair of pliers
    • Remove the three T25 Torx bolts from the compressor
    • Pull the motor off of the compressor
  3. step : Preparing the New Motor (3:31)
    • Disconnect the hose from the old motor
    • Push the hose onto the motor
    • Pry the wiring harness from the old motor
    • Remove the Phillips screw from the old motor
    • Remove the wire ties from the wiring harness
    • Pull back the wiring covers
    • Clip the wires with wire cutters
    • Match the wires to the corresponding, color-coded ones on the new motor
    • Clip each wire
    • Strip the end of each wire
    • Push the wires into the splices
    • Crimp the splices with pliers
    • Put the compressor in a vice
    • Twist the drier off of the compressor
    • Remove the three T25 screws from the old motor bracket
  4. step : Preparing the new Drier (7:32)
    • Note that there is a spring inside the drier
    • Carefully twist off the lid of the drier
    • Pull the spring out of the drier
    • Pull the gasket out of the drier
    • Pull the screen out of the drier
    • Pull the pad out of the drier
    • Remove the beads from the drier
    • Pull the second pad out of the drier
    • Pull the second screen out of the drier
    • Insert the new screen into the drier
    • Insert the new pad into the drier
    • Pour the new beads into the drier
    • Insert the second new pad into the drier
    • Insert the second new screen into the drier
    • Put the new spring in place
    • Put a new gasket on the drier lid
    • Twist on the drier lid
  5. step : Reconstructing the Compressor (9:10)
    • Put a new O-ring onto the drier end
    • Twist the drier onto the compressor
    • Loosen the 8mm bolt from the compressor
    • Insert the wire from the old compressor
    • Tighten the 8mm bolt
    • Reconnect the wiring harness to the drier
    • Push the pads into the bracket
    • Put the compressor onto the bracket
    • Insert the three T25 screws to attach the new motor to the bracket
    • Seat the wiring harness in the bracket
  6. step : Reinstalling the Compressor (10:41)
    • Connect the compressor wiring harness
    • Hang the compressor in place by its bolts
    • Tighten the 12mm nuts onto the compressor bracket
    • Push the compressor hoses back into place

Tools needed for replacement:

    General Tools

  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers
  • Wire Cutters
  • Wire End Cutters

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 12mm Socket
  • 8mm Socket

  • Specialty Tools

  • Vise-Grips

  • Torx Drivers & Sockets

  • T25 Torx Driver

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Great service and parts!
My order showed up in days and had all the info and parts necessary to do my own repair. If you're not afraid of a little dirt and grease doing your own repair, 1AAuto is the way to go!
July 30, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 2 questions Browse 2 questions and 6 answers
Does this kit work with the vehicles computer so it won't show suspension fault code?
Lilrebel66 on Jun 6, 2017
BEST ANSWER: Yes the system works well with my 2002 Suburban half ton. new load leveling pump and rear shocks are good. I do not care for the front shocks. They are too soft. I think any after mark shock for the front would work, except you don't have the grounding plug attachment to substitute for the active circuitry of the old system. I would buy the package with the heavy duty front shocks. I am going to replace my new standard front shocks with the originals which I kept.
\\\
Does this fit 2000 yukon Denali ?
James on Apr 21, 2017
BEST ANSWER: Yes, these will be proper fit for your 2000 Yukon Denali.

Vehicle Fit

Year Make Model Description
2002-2006Cadillac Escalade Cadillac Escalade 5 Piece Set Air Suspension Kit
2003-2006Cadillac Escalade ESV Cadillac Escalade ESV 5 Piece Set Air Suspension Kit
2002-2006Cadillac Escalade EXT Cadillac Escalade EXT 5 Piece Set Air Suspension Kit
2003-2006Chevy Avalanche 1500 Chevy Avalanche 1500 5 Piece Set Air Suspension Kit
2000-2006Chevy Suburban 1500 Chevy Suburban 1500 5 Piece Set Air Suspension Kit
2000-2006Chevy Tahoe Chevy Tahoe 5 Piece Set Air Suspension Kit
2001-2006GMC Yukon GMC Yukon 5 Piece Set Air Suspension Kit
2000-2006GMC Yukon XL 1500 GMC Yukon XL 1500 5 Piece Set Air Suspension Kit

This part replaces:

  • OE # 15254590
  • OE # 19300047
  • OE # 20930288
  • OE # 22187151
  • OE # 22187155
  • OE # 22187157
  • OE # 22187159
  • OE # 22400248
  • OE # 22400884
  • OE # 22941806
  • OE # 88965339
  • Arnott SK-2126, AS-2127, P-2793, SK-2760
  • Arnott Supersession P-2204
Part #: ARSFK00016


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Arnott
Brand #: SK-2126, AS-2127, P-2793, SK-2760

How-to Video:

(11:49 min)