Replaces

Acura TL Honda Accord Strut & Spring Assembly TRQ SCA57524 - 1ASTS00804

Frequently bought together

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Rear Seat (0:28)
    • Pull out on the T-handle on either side and pull the seat up
    • Remove the 10mm bolt from the seat on each side pillar
    • Insert the key to the lock to unlock the seat
    • Lay the back seat down
    • Remove the side pillar on each side
    • Unclip the black seat trim from the plastic tabs
    • Remove the two nuts from the strut tower mounting bolts (not the spring-loaded center bolt)
  2. step : Removing the Wheel (2:53)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  3. step : Removing the Rear Strut (3:45)
    • Loosen the bottom 17mm nut from the strut
    • Remove the 17mm bolt
    • Remove the 14mm bolt from the upper sway bar link bracket
    • Set the bracket to the side
    • Pry the shock down and out with a pry bar
  4. step : Installing the Rear Strut (6:09)
    • Remove the two upper nuts from the strut
    • Using a pry bar, set the rear strut into place
    • Place the upper nuts on by hand
    • Tighten the upper nuts with a 15mm socket and ratchet
    • Torque the bolts to 37 foot-pounds
    • Insert the lower end of the strut into place and put the bolt in by hand
    • Tighten the 17mm lower bolt to the bottom of the strut
    • Tighten the 14mm bolt to the upper sway bar link bracket
    • Torque the bottom strut bolt to 43 foot-pounds
  5. step : Reinstalling the Seat (11:42)
    • Reinstall the top black trim to the back seat
    • Clip the pillar trim to both sides
    • Tighten the 10mm bolt to the trim on both sides
    • Press the back into place
    • Line up the seat belts and snap the bottom of the seat in on both sides
  6. step : Reattaching the Wheel (13:48)
    • Slide the wheel into place
    • Start the 19mm lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    Ratchets & Related

  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 14mm Socket
  • 15mm Socket
  • 17mm Socket
  • 19mm Socket
  • 10mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2004-2008Acura TL Acura TL Rear Strut & Spring Assembly Driver or Passenger Side TRQ SCA57524
2003-2004Honda Accord Honda Accord Rear Strut & Spring Assembly Driver or Passenger Side TRQ SCA57524
2005-2007Honda Accord Honda Accord Rear Strut & Spring Assembly (excluding Hybrid Models) Driver or Passenger Side TRQ SCA57524
Part #: 1ASTS00804


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

TRQ
Brand #: SCA57524