Replaces

Acura MDX Honda Pilot Steering & Suspension Kit - 1ASFK04818

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as an 8 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:58)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Stabilizer Link (1:52)
    • Hold the upper stabilizer link stud with a 19mm wrench
    • Remove the upper nut from the stabilizer link with a 17mm socket and ratchet
    • Hold the lower stabilizer link stud with a 19mm wrench
    • Remove the lower nut from the stabilizer link with a 17mm socket and ratchet
    • Pull off the stabilizer link
  3. step : Reinstalling the Stabilizer Link (3:30)
    • Push the stabilizer link into place
    • Start the 17mm nuts by hand
    • Hold the upper stabilizer link stud with a 19mm wrench
    • Fasten the upper nut onto the stabilizer link with a 17mm wrench
    • Hold the lower stabilizer link stud with a 19mm wrench
    • Fasten the lower nut onto the stabilizer link with a 17mm wrench
  4. step : Reattaching the Wheel (3:51)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • Ratchet

  • Sockets - Metric

  • 19mm Socket
  • 17mm Socket

  • Wrenches - Metric

  • 17mm Wrench
  • 19mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2001-2005 Acura MDX 8 Piece Set Steering & Suspension Kit
  • 2003-2005 Honda Pilot 8 Piece Set Steering & Suspension Kit

This part replaces:

  • Moog K80281
  • Moog K90349
  • OE # 53560S3VA02
  • OE # 53540S3VA02
  • Moog EV471
  • Moog ES3717
  • Moog ES3716
  • OE # 53010S3VA01, 53010S3VA02, A01
  • OE # 06513-S0X-A00, 51320S0XA02
Part #: 1ASFK04818


How-to Video:

(04:40 min)