Replaces

2010-15 Chevy Camaro Wheel Bearing & Hub Assembly - 1ASHR00283

Specifications:

  • Fits LH (Driver Side) or RH (Passenger Side) Rear
  • 3 Bolt Flange
  • Fits 5 Lug Wheel
  • New wheel studs installed
  • Direct replacement
  • Built to strict quality control standards
Precision Engineered:

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials:

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement:

Guaranteed to fit and function correctly for your specific application.

Part Details

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

BHA54369 Axle / Spindle Nut Torque Specification

  1. step : Removing the Wheel (0:56)
    • Loosen the 22mm lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Separating the Axle from the Hub (1:19)
    • Put the transmission in gear
    • Put the parking brake on
    • Loosen the 32mm axle nut
    • Remove the axle nut
    • Loosen the axle spines with a hammer and punch
  3. step : Removing the Brakes (1:54)
    • Remove the two 16mm bolts from the brake caliper
    • Pull off the brake caliper
    • Hang the caliper aside with bungee cords
    • Remove the T30 Torx screw from the brake rotor
    • Release the parking brake
    • Tap the face of the rotor with a hammer to loosen it
    • Pull off the brake rotor
  4. step : Removing the Hub (3:12)
    • Remove the four 13mm bolts that hold the hub to the wheel spindle
    • Apply a two-jaw puller to the hub
    • Tighten the puller with a socket and ratchet
    • Remove the two-jaw puller
    • Pull the hub off the axle
    • Pull the washer off the axle with a pick
  5. step : Installing the Hub (4:21)
    • Slide the new washer onto the axle
    • Slide the bearing splines onto the axle
    • Start the four 13mm bolts that hold the hub to the wheel spindle
    • Tighten the 13mm bolts to 85 foot-pounds of torque
  6. step : Installing the Brakes (5:04)
    • Put the rotor into place
    • Insert the T30 screw into the rotor
    • Remove the bungee cord from the caliper
    • Put the caliper into pace
    • Start the two 16mm bolts into the caliper
    • Tighten the 16mm bolts to 30 foot-pounds
    • Tighten the 16mm bolts 90 degrees further
  7. step : Installing the Wheel (5:59])
    • Start the axle nut onto the axle
    • Tighten the axle nut to 200 foot-pounds
    • Slide the wheel into place
    • Start the five 22mm lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 140 foot-pounds in a star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Pick
  • Floor Jack
  • Funnel

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • 2 Jaw Gear Puller

  • Torx Drivers & Sockets

  • T30 Torx Bit

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2010-2015Chevy Camaro Chevy Camaro Rear Wheel Bearing & Hub Assembly V8 6.2L (excluding ZL1 Models)
2010-2015Chevy Camaro Chevy Camaro Rear Wheel Bearing & Hub Assembly V6 3.6L with Manual Transmission

This part replaces:

  • Hollander 538-00225
  • OE # 13500401, 13504969, 7467850
Only 2 left in stock
Part #: 1ASHR00283


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(07:03 min)