Replaces

2010-15 Chevy Camaro Wheel Bearing & Hub Assembly Rear Pair Timken HA590348 - TKSHS00549

Part Details

  • Quantity: Pair
  • Front or Rear Location: Rear

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: HA590348

These replacement hub & bearing assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • Replaces dealer part number: 13500401
  • 3 Bolt Flanges
  • Fit 5 Lug Wheels
  • New wheel studs installed
  • Direct replacements
  • Built to strict quality control standards

Note:
These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:56)
    • Loosen the 22mm lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Separating the Axle from the Hub (1:19)
    • Put the transmission in gear
    • Put the parking brake on
    • Loosen the 32mm axle nut
    • Remove the axle nut
    • Loosen the axle spines with a hammer and punch
  3. step : Removing the Brakes (1:54)
    • Remove the two 16mm bolts from the brake caliper
    • Pull off the brake caliper
    • Hang the caliper aside with bungee cords
    • Remove the T30 Torx screw from the brake rotor
    • Release the parking brake
    • Tap the face of the rotor with a hammer to loosen it
    • Pull off the brake rotor
  4. step : Removing the Hub (3:12)
    • Remove the four 13mm bolts that hold the hub to the wheel spindle
    • Apply a two-jaw puller to the hub
    • Tighten the puller with a socket and ratchet
    • Remove the two-jaw puller
    • Pull the hub off the axle
    • Pull the washer off the axle with a pick
  5. step : Installing the Hub (4:21)
    • Slide the new washer onto the axle
    • Slide the bearing splines onto the axle
    • Start the four 13mm bolts that hold the hub to the wheel spindle
    • Tighten the 13mm bolts to 85 foot-pounds of torque
  6. step : Installing the Brakes (5:04)
    • Put the rotor into place
    • Insert the T30 screw into the rotor
    • Remove the bungee cord from the caliper
    • Put the caliper into pace
    • Start the two 16mm bolts into the caliper
    • Tighten the 16mm bolts to 30 foot-pounds
    • Tighten the 16mm bolts 90 degrees further
  7. step : Installing the Wheel (5:59])
    • Start the axle nut onto the axle
    • Tighten the axle nut to 200 foot-pounds
    • Slide the wheel into place
    • Start the five 22mm lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 140 foot-pounds in a star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Pick
  • Floor Jack
  • Funnel

  • Materials, Fluids, and Supplies

  • Bungee Cord

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • Complete Metric Socket Set

  • Specialty Tools

  • 2 Jaw Gear Puller

  • Torx Drivers & Sockets

  • T30 Torx Bit

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Rear Wheel Hubs
Product came in 2 days. Installed them that night. A direct replacement part that fit like a glove replaced both hubs in less than 1 hour
July 16, 2018
Purchased
3 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
2010-2015Chevy Camaro Chevy Camaro Rear Wheel Bearing & Hub Assembly V8 6.2L (excluding ZL1 Models) Pair Timken HA590348
2010-2015Chevy Camaro Chevy Camaro Rear Wheel Bearing & Hub Assembly V6 3.6L with Manual Transmission Pair Timken HA590348

This part replaces:

  • Timken HA590348
  • Hollander 538-00225
  • OE # 13500401
Only 1 left in stock
Part #: TKSHS00549


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Timken
Brand #: HA590348

How-to Video:

(07:03 min)